Home » Konica Minolta Manuals » Printers » Konica Minolta AccurioPress 6120 » Manual Viewer

Konica Minolta AccurioPress 6120 AccurioPress 6136/6136P/6120 Daily Maintenanc - Page 20

Cleaning the Output Unit

View all Konica Minolta AccurioPress 6120 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

1.6 Cleaning the Output Unit 1 1.6 Cleaning the Output Unit If the output unit is dirty, follow the steps below to clean it. 7CAUTION - Always check the cleaning locations before turning the main body on. - If the power is turned on while the main body doors are closed, the fusing unit may become hot and you may be burned when cleaning around the fusing unit. NOTICE When cleaning, exercise care to prevent any dirt from falling into the paper feed route. 1 Open the front door of the main body and the left side door of the main body. 2 Turn ON the main power switch, and turn ON the sub power switch. 3 Lower the lever [M4] clockwise. 4 Hold the lever [M4], and pull out the duplex part. AccurioPress 6136/6136P/6120 1-15

Section	Page
Table of contents	4
1 Daily Care	7
1.1 Daily Cleaning	7
Care timing	7
Care requirements	7
1.2 Weekly Cleaning	8
Care timing	8
Care requirements	8
1.3 Cleaning the Scanning Area	9
1.4 Cleaning the Fusing Unit	11
1.5 Cleaning the Duplex Part	14
1.6 Cleaning the Output Unit	20
1.7 Cleaning the Paper Feed Unit	23
2 Both Sides Adjust	27
2.1 What is Both Sides Adjust?	27
2.2 Adjustment flow to use paper of a new brand, weight, or size	28
2.2.1 Adjustment Timing	28
2.2.2 Adjustment Order	28
2.3 Regular adjustment flow	29
2.3.1 Adjustment Timing	29
2.3.2 Adjustment Order	29
2.3.3 Periodical Both Sides Adjustment Function	30
2.4 Adjustment flow for each job	31
2.4.1 Adjustment Timing	31
2.4.2 Adjustment Order	31
2.5 How to Operate the Both Sides Adj. Item	32
2.5.1 Fine-adjusting the gap between side guide plates of Paper Feed Unit PF-710	32
2.5.2 [Front] Adjustment	36
2.5.3 [Scan Meas.] Adjustment	41
2.5.4 [Rotate/Skew] Adjustment	49
2.5.5 [Gap] Adjustment (Back side adjustment)	52
2.5.6 [AutoMeasure] Adjustment	57
2.5.7 Registering Paper Profile	59
2.5.8 Back Side Fine Adjustment	62
2.5.9 [Periodical Both Sides Adj.]	67
3 Quality Adjustment	71
3.1 Quality Adjustment for Image Controller	71
3.2 Regular adjustment flow (Standard)	72
3.2.1 Adjustment timing	72
3.2.2 Adjustment sequence	72
3.3 Regular adjustment flow (High accuracy)	73
3.3.1 Adjustment Timing	73
3.3.2 Adjustment Order	73
3.4 Adjustment flow to use a new type of paper	74
3.4.1 Adjustment timing	74
3.4.2 Adjustment sequence	74
3.5 Adjustment Flow when changing the screen	75
3.5.1 Adjustment timing	75
3.5.2 Adjustment sequence	75
3.6 Details of quality adjustment items	76
3.6.1 Setting of the Custom Screen	76
3.6.2 [Gamma Automatic Adj.]	78
Performing [Gamma Automatic Adj.]	78
3.6.3 [Density Balance Adjustment]	80
Adjustment flow when changing the screen	80
Saving the measured data of the density balance	90
Registering the adjusted value of the density balance in the machine	91
3.6.4 [Density Balance Auto. Adj.]	97
3.6.5 [Maximum Density Adjustment]	106
3.6.6 [Max. Density Auto Adj.]	108
3.6.7 Checking the Color Density Control Setting	110
3.6.8 [Color density manual control]	112