Home » Konica Minolta Manuals » Printers » Konica Minolta AccurioPress 6120 » Manual Viewer

Konica Minolta AccurioPress 6120 AccurioPress 6136/6136P/6120 Daily Maintenanc - Page 39

Press the number of each point, and use the touch panel keypad to enter the measured length.

View all Konica Minolta AccurioPress 6120 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

2.5 How to Operate the Both Sides Adj. Item 2 11 Check the lengths at points [2], [4], [6], and [8] on the second and third output charts. Be sure to make note of the measurement lengths. When the lengths at points [2], [4], [6], and [8] are within the respective ranges shown below, press [Close], then press [OK] to finish the adjustment. When the lengths at points [2], [4], [6], and [8] are outside the respective ranges shown below, also measure the lengths at points [1], [3], [5], and [7], then proceed to step 12. [2]: 200 mm ^ 0.3 mm [4]: 200 mm ^ 0.3 mm [6]: 200 mm ^ 0.3 mm [8]: 200 mm ^ 0.3 mm 12 Press the number of each point, and use the touch panel keypad to enter the measured length. Press [Clear] to reset the value. AccurioPress 6136/6136P/6120 2-14

Section	Page
Table of contents	4
1 Daily Care	7
1.1 Daily Cleaning	7
Care timing	7
Care requirements	7
1.2 Weekly Cleaning	8
Care timing	8
Care requirements	8
1.3 Cleaning the Scanning Area	9
1.4 Cleaning the Fusing Unit	11
1.5 Cleaning the Duplex Part	14
1.6 Cleaning the Output Unit	20
1.7 Cleaning the Paper Feed Unit	23
2 Both Sides Adjust	27
2.1 What is Both Sides Adjust?	27
2.2 Adjustment flow to use paper of a new brand, weight, or size	28
2.2.1 Adjustment Timing	28
2.2.2 Adjustment Order	28
2.3 Regular adjustment flow	29
2.3.1 Adjustment Timing	29
2.3.2 Adjustment Order	29
2.3.3 Periodical Both Sides Adjustment Function	30
2.4 Adjustment flow for each job	31
2.4.1 Adjustment Timing	31
2.4.2 Adjustment Order	31
2.5 How to Operate the Both Sides Adj. Item	32
2.5.1 Fine-adjusting the gap between side guide plates of Paper Feed Unit PF-710	32
2.5.2 [Front] Adjustment	36
2.5.3 [Scan Meas.] Adjustment	41
2.5.4 [Rotate/Skew] Adjustment	49
2.5.5 [Gap] Adjustment (Back side adjustment)	52
2.5.6 [AutoMeasure] Adjustment	57
2.5.7 Registering Paper Profile	59
2.5.8 Back Side Fine Adjustment	62
2.5.9 [Periodical Both Sides Adj.]	67
3 Quality Adjustment	71
3.1 Quality Adjustment for Image Controller	71
3.2 Regular adjustment flow (Standard)	72
3.2.1 Adjustment timing	72
3.2.2 Adjustment sequence	72
3.3 Regular adjustment flow (High accuracy)	73
3.3.1 Adjustment Timing	73
3.3.2 Adjustment Order	73
3.4 Adjustment flow to use a new type of paper	74
3.4.1 Adjustment timing	74
3.4.2 Adjustment sequence	74
3.5 Adjustment Flow when changing the screen	75
3.5.1 Adjustment timing	75
3.5.2 Adjustment sequence	75
3.6 Details of quality adjustment items	76
3.6.1 Setting of the Custom Screen	76
3.6.2 [Gamma Automatic Adj.]	78
Performing [Gamma Automatic Adj.]	78
3.6.3 [Density Balance Adjustment]	80
Adjustment flow when changing the screen	80
Saving the measured data of the density balance	90
Registering the adjusted value of the density balance in the machine	91
3.6.4 [Density Balance Auto. Adj.]	97
3.6.5 [Maximum Density Adjustment]	106
3.6.6 [Max. Density Auto Adj.]	108
3.6.7 Checking the Color Density Control Setting	110
3.6.8 [Color density manual control]	112