Konica Minolta Kodak i620 User Guide - Page 12

Stop/Pause and Start/Resume buttons, Power switch, Exit deflector optional, Paper Present Sensor

Get Konica Minolta Kodak i620 PDF manuals and user guides View all Konica Minolta Kodak i620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

7 Stop/Pause and Start/Resume buttons - Stop/Pause (white with red triangle) button: press once to temporarily pause scanning (the green button can then use used to resume scanning). Press twice to stop scanning (end of job). Start/Resume (green) button: to start scanning. 8 LEDs- illuminate or flash from top to bottom as follows: Illuminates when the power is turned on and the scanner is idle. This indicator will flash if the scanner is in "sleep" or lamp saver mode. illuminates when the scanner is enabled and/or scanning, and flashes when the scanner is powering up. flashes when a document has jammed in the transport or when a multi-feed has been detected. Illuminates when a usercorrectable error has been detected. Illuminates when you need to call Service. Refer to Chapter 6, Troubleshooting, for complete descriptions of the LED indicators. 9 Power switch - press the power switch on (I) or off (O) as required. 10 Exit deflector (optional) - aids in document stacking. 11 Paper Present Sensor - detects the presence of documents in the elevator tray. 12* Height Adjustment Wire - located underneath the output tray (not shown in photo), this wire can be pulled out to raise the front of the output tray. 2-4 A-61500 April 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
2-4
A-61500
April 2007
7
Stop/Pause and Start/Resume buttons
—
8
LEDs
— illuminate or flash from top to bottom as follows:
Illuminates when the power is turned on and the scanner is idle.
This indicator will flash if the scanner is in “sleep” or lamp saver
mode.
illuminates when the scanner is enabled and/or scanning, and
flashes when the scanner is powering up.
flashes when a document has jammed in the transport or
when a multi-feed has been detected. Illuminates when a user-
correctable error has been detected.
Illuminates when you need to call Service.
Refer to Chapter 6,
Troubleshooting
, for complete descriptions of
the LED indicators.
9
Power switch
— press the power switch on (I) or off (O) as
required.
10
Exit deflector (optional)
— aids in document stacking.
11
Paper Present Sensor
— detects the presence of documents in
the elevator tray.
12*
Height Adjustment Wire
— located underneath the output tray
(not shown in photo), this wire can be pulled out to raise the front of
the output tray.
Stop/Pause
(white with red triangle) button:
press once to temporarily pause scanning (the
green button can then use used to resume
scanning). Press twice to stop scanning
(end of job).
Start/Resume
(green) button: to start scanning.