Konica Minolta PS7000 PS7000 Operator Manual (Printer Version)
Konica Minolta PS7000 Manual
View all Konica Minolta PS7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Konica Minolta PS7000 manual content summary:
- Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 1
0818-7704-13 PS7000 PR version Operator´s Manual - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 2
should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the next section before using this device. It contains important information related to user safety and preventing equipment problems. Make sure you observe all of - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 3
these conditions be found, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. • In principle, do not use an extension cord. Use of an extension cord could cause a fire or electrical shock. Contact your authorized - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 4
smoke, or unusual odor or noise, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, a fire or electrical shock could result. • If this product has been dropped or its cover damaged - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 5
CAUTION • Do not use flammable sprays, liquids, or gases near this product, as a fire could result. • Do not leave a toner unit or drum unit in a place within easy reach of children. Licking or ingesting any of these things could injure your health. • Do not let any object plug the ventilation holes - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 6
. Failure to do this could damage the cord or cable, resulting in a fire, electrical shock, or breakdown. • When moving this product, always hold it by the locations specified in the operator's manual or other documents. If the unit falls it may cause severe personal injury. The product may also - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 7
other gases or chemicals are present. Failure to do so may shorten the service life of the product, cause damage or decrease performance. • Do not use an environment with a temperature outside the range specified in the operator's manual, as a breakdown or malfunction could result. • Do not attempt - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 8
any questions or comments about Minolta, our product or service, please let us know. Our fax number is 800-237-8087 (for U.S.A. and Canada). Thank you again. This operator's manual explains how to operate the unit and replenish its supplies. It also gives some troubleshooting tips as well as general - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 9
Book Scanner (herein after referred to as the Scanner). This operator's manual explains the various functions provided by the Scanner. It also gives some maintenance as well as troubleshooting tips. Before operating the Scanner, read this manual accordance with the instruction manual, may cause - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 10
iii Introduction Copyright Books, magazines, journals and other materials may be copyrighted. Unauthorized appropriate. Post a copy of the above notice where it will be clearly visible to users of the scanner. Scanning into a computer and subsequent printing of the following is also prohibited by law - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 11
. This declaration is valid for the area of the European Union (EU) only. Product Type Product Name Options Accessory Standards EC Directives Book Scanner PS 7000 Foot Switch, MSP3000 PR I/F Kit Safety: EMC EN60 950 / 1992 A1, A2, A3, A4 (Safety of information technology equipment, including - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 12
Introduction Copyright Books, magazines, for criticism or review, for reporting current events and various acts in relation to education, libraries and public administration. The Minolta Co., Ltd. No part of this documentation may be reproduced, transmitted, transcribed, stored in a retrieval scanner - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 13
the printer is operated according to the instructions provided in this manual. user operation. Internal Laser Radiation Maximum Radiation Power: 8.8 ×10-4(W) Wave Length: 770-810 (nm) This is a Class IIIb Laser Diode Assy. that has an invisible laser beam. The print head unit is NOT A FIELD SERVICE - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 14
vii Safety Information (MSP3000 Printer) For Denmark ADVARSEL: Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. Klasse 1 laser produkt der opfylder IEC60825 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 15
viii Safety Information (MSP3000 Printer) For Norway ADVARSEL: Dersuom apparatet brukes på annen måte enn spesifisert i denne bruksanvisning, kan brukeren utsettes for unsynlig laserstråling som overskrider grensen for laser klasse 1. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 16
ix Safety Information (MSP3000 Printer) OZONE RELEASE (For all Users) During printer operation, a small quantity of ozone is released. This amount is not large enough to cause any adverse affects or harm. However, be sure the room - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 17
names for the printer. Chapter 5 Troubleshooting Describes error and warning messages that appear on the control panel, and procedures for eliminating these problems. Chapter 6 Maintenance Describes daily maintenance required for satisfactory operation of the Scanner. Chapter 7 Specifications - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 18
3-1 Lamp status 3-2 Half intensity 3-2 Full intensity 3-2 Turning the Scanner ON and OFF 3-3 Turning on 3-3 Turning off 3-4 Placing the original 3-5 Scanning procedures 3-6 Book/Sheet modes 3-10 Book mode 3-10 Sheet mode 3-11 Note on originals 3-12 Menu flow chart 3-16 User Mode - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 19
3-51 SCSI port settings 3-53 Exiting Utility mode 3-54 Chapter 4 Printer Using the Printer 4-1 Parts of the Printer 4-1 Troubleshooting and Maintenance 4-3 Replenishing the Paper Supply 4-3 Replacing the Toner Cartridge 4-7 Clearing Misfeeds 4-10 Solving Irregular Printing Problems 4-13 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 20
xiii Contents Chapter 6 Maintenance Maintenance 6-1 Daily checks 6-1 Cleaning 6-1 Cleaning the MSP 3000 Printer 6-2 Chapter 7 Specifications Product specifications 7-1 For Key Operator's Use 7-3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 21
xiv Contents - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 22
Precautions for Installation & Operation Chapter 1 Chapter 1 Precautions for Installation & Operation - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 23
book table is less than 1000 lx (e.g. 4.5 m x 6.5 m area with ceiling height of 2.6 m, and 12 or less 40 W fluorescent lamps). ! A place where light from the lighting system or the outside through windows does not reflect on the steel mirror or hit the Scanner the Scanner and the Scanner's ground - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 24
Chapter 1 1-2 Installation Moving the Scanner Please contact your authorized dealer before moving the Scanner to a new installation location. Space space shown in the figure below to ensure easy operation and maintenance of the Scanner. 150 mm 5-7/8" 150 mm 5-7/8" 150 mm 5-7/8" 745 mm 29-3/8" - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 25
a damaged or cracked power cord or interface cable unrepaired. If any of these conditions are found, immediately shut down the Scanner, unplug the power cord, and call your authorized dealer for appropriate action. ! NEVER place an object on the lamp unit. ! ALWAYS completely insert the power cord - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 26
When moving the Scanner, be sure to disconnect the power cord and the interface cable. ! When transporting the Scanner, contact your authorized Dealer. NOTE Never hold any parts other than the parts identified with arrows in the figure (e.g.,lamp cover, book table), or the Scanner may have trouble. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 27
! NEVER drop paper clips, staples, or other small pieces of metal into the printer. If this occurs, contact your authorized Dealer. ! NEVER place the printer or the cabinet on the power cord or interface cables of other electrical equipment. ! NEVER leave a damaged or cracked power cord or interface - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 28
Overview Chapter 2 Chapter 2 Overview - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 29
2-1 Features The Scanner is designed to scan books set face up on the book table. This makes setting the book very easy and reduces concerns that the book may be creased or damaged. In addition, warped text lines and text compression are corrected, ensuring clearer images. Various options such as a - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 30
connected to a personal computer) The Scanner is connected to a personal computer and the scanned images can be uploaded to the computer. This manual describes the PR version. • Connection to a personal computer and printer can be switched using [Output] in the [User Mode] menu. • A PC interface kit - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 31
and functions 1 9 8 2 3 4 5 10 11 6 7 12 13 16 18 15 14 17 19 1. Scanner unit: 2. Lamp unit: 3. Control panel: 4. Shading plate: 5. Steel mirror: 6. Book table: 7. Table center: 8. Start key: 9. Power switch: 10. Printer connector: 20 The CCD sensor housed in this unit scans the original - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 32
2-4 Part identification and functions Overview Chapter 2 11. SCSI connector: Connect the SCSI cable included in the interface kit. When multiple SCSI devices are connected to the personal computer, connect the Scanner at the end of the SCSI chain. (Optional PC interface kit is required) The total - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 33
Spread Single Text 8 Book Split Photo Panel Reset 9 6 Adjusts the contrast (luminosity) of the display. Allows you to customize settings. Recalls settings previously registered in User Mode. Displays the current settings. Displays current status, operation instructions, warning messages, and - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 34
Data Sheet Eras put ious Spread Single Book Split Text Photo Panel Reset Refer to page 3-16 "Menu flow chart" for details of each menu. 3. Job Recall key Recalls settings previously registered in User Mode. Pressing this key displays preset programs (scanner settings). The desired program can be - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 35
. Contrast User Mode Job Recall Mode Check FRAME MASK FINGER MASK CENTER ERASE ORIGINAL PRIORITY CONNECTION ON CENTERING OFF OFF OFF Book Auto Quality Next Printer Spread Single Book Split Text Photo Panel Reset Overview Chapter 2 5. Display Operating status, operation instructions - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 36
Split: Right and left pages are scanned separately. Contrast User Mode Job Recall Mode Check Spread Single Book Split Text Photo Panel Reset Overview Chapter 2 8. Image key The image type can be selected to suit the original. The lamp of the selected mode lights. Text: Suitable for scanning - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 37
settings to their default settings, and displays the main menu. All settings revert to default settings when the power switch is turned on. Contrast User Mode Job Recall Mode Check Spread Single Book Split Text Photo Panel Reset Overview Chapter 2 Default settings are as follows. Item Connect - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 38
Operation Chapter 3 Chapter 3 Operation - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 39
careful not to knock your head against the scanner unit. Do not hold the sides when pushing the book table down, or your hands or fingers may be caught. Place your hand on the top surface of the table. Do not look directly at the lamp light visible through the front slits or - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 40
or five minutes in the Utility mode. Full intensity The Scanner's lamp lights at full intensity when the Scanner is reading the original. The lamp returns to half intensity after scanning is completed. NOTE The halogen lamp used in the Scanner is safe and not hazardous to health. However, never look - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 41
Welcome to PS7000. Initializing] appears on the display and the start key turns red. The Scanner can be operated when the start key turns green. Start key NOTE When the printer interface cable is not connected properly, an error message appears on the display. When the message [Start Appli./Driver - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 42
Turning off 1 Turn the switch off ("O" position). 3-4 Turning the Scanner ON and OFF Operation Chapter 3 NOTE •Never turn the power switch off while the Scanner is reading the original. •Turn off the Scanner before turning off the printer. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 43
original Place the original face up on the book table, aligning the top edge of the book with the stopper on the book table, and the spine of the book with the center mark. Check that the original is positioned with the corresponding size guide, if possible. When placing the original, observe the - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 44
Chapter 3 3 Place the original face up on the book table, aligning the top edge of the book with the stopper on the book table, and the spine of the book with the center mark. Check that the original is positioned with the corresponding size guide, if possible. NOTE In placing the original, make - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 45
. Spread: Entire area (both pages) is scanned as one sheet. Single: Only one page (right or left) is scanned. Book Split: Both pages are scanned separately, one page at a time. The lamp of the selected mode lights. 5 Hold the edges of both pages in the middle with your hands, and press the - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 46
original is placed in the effective Auto Focus range. 6 Press the Start key. Either key can be pressed when [Spread] is selected. When [Single] or [Book Split] is selected, press the key on the side to be scanned. The pressed Start key turns red and scanning is started. When scanning is - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 47
into the space enclosed by the scanner unit and the right and left edges of the book, or the Scanner will not be able to obtain Scanner fails to read the original correctly, a buzzer goes off, a warning message appears on the display, and scanning is stopped. Refer to page 5-2 "Troubleshooting - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 48
°, proper correction may not be made. Auto focus This function is available only to Book mode. The original height is detected, and the focal point of the Scanner can be adjusted to be within a range from 0 to 65 mm above the book table according to the detected original height. Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 49
can be set to be within a range from 0 to 50 mm above the book table in 6 steps in 10 mm increments. When scanning a solid surface, adjust the detection. Set each function as follows to cancel the Auto function. • Expo (Manual) • Zoom (Fixed magnification) • Cent Eras (OFF) • Masking (OFF) • - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 50
4.Foot 5.Head 6.Guter The Scanner is designed for exclusive use in scanning images from a book or file. Note, however, that it may not make reliable images from any of the following types of originals. (If a warning message appears, refer to page 5-2 "Troubleshooting for warning messages".) If any - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 51
the top edge of the original, place the original upside down on the book table for scanning. If bookmarks are placed in the original, put them mm Operation Chapter 3 Bookmark 4. Originals with both text and photographs The Scanner provides you with two Image modes, Text and Photo. When an original - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 52
so that the binding section is lowered to the extent that the Auto Focus function is 65 mm effective. Push the center of the book table with your hands (see figure). The depth can be adjusted to two levels. Push down either side of the table and release it to - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 53
whose binding must be carefully protected. 1 Assemble the angle book holder as shown in the figure. 2 Insert the holder into the groove on the book table. 3 Change the stand position to adjust the angle of the book holder. 4 Position the book and secure it to the holder with the attached band as - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 54
to 20 mm (in 2.5 mm increments). Output Select an external device (printer or personal computer) to be connected to the Scanner. Previous Auto set (Available only in Book mode) Cent set -2.5 mm Wide +2.5 mm Wide OK PC Printer OK * Select [OK] to return to the main menu. Job Recall Recalls - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 55
3-17 Menu flow chart The following items can be set from the main menu: In Inch Operation Chapter 3 Main Menu Edit Turns the Center Erase, Frame Masking, Finger Masking, and Centering functions on and off. Expo Sets exposure for scanning. In addition to turning [Auto] on and off, nine levels of - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 56
Main menu: In Metric 3-18 Menu flow chart Operation Chapter 3 Main Menu Edit Turns the Center Erase, Frame Masking, Finger Masking, and Centering functions on and off. Expo Sets exposure for scanning. In addition to turning [Auto] on and off, nine levels of exposure can be selected using [Lite] - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 57
Pnl set Connect Reset Previous PC Printer Previous OK Set cfm Previous OK and activated for the current and subsequent operations. Auto clr Lamp Off Save mode Previous 1 min. 3 min. 10 min the current and subsequent operations. SCSI set ID number of the SCSI port is customized for the current - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 58
User Mode Press the User Mode key on the control panel. The User Mode menu is displayed. Contrast User Mode Job Recall Mode Check 3-20 Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 59
. 1 Select [Save Data] from the User Mode menu. The program registration screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Select [OK] to register the settings. Select [Confirm] to review the settings. Select [Previous] to return to the program registration screen. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 60
to page 3-10 "Book/Sheet modes" for details. Select [Book/Sheet] from the User Mode menu. The book/sheet setting screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Operation Chapter 3 Select [Book mode] when scanning a thick original (books or dictionaries). Select - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 61
Chapter 3 3-23 User Mode Book mode setting function Normally, "Book mode" is used in "Auto" setting. In the following cases, however, set the distance between the stopper and the original. N A hardcover book is scanned N The original height cannot be detected (a waning message "Book Size in Not - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 62
adjusted to be within a range of 0 to 50 mm in 10 mm increments. The adjusted setting value appears on the display. 3-24 User Mode Set Thickness (~50) 20 mm Book Sheet -10 mm +10 mm mode mode OK Select [OK] to return to the main menu. Operation Chapter 3 NOTE When Sheet mode - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 63
shadow generated in the center of the open book is removed. Spread mode Erasing width Single or Book Split mode Erasing width Operation Chapter 3 Select [Cent Eras] from the User Mode menu. The center erase setting screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 64
The erasing width can be adjusted from 2.5 to 20 mm (0.1" to 0.8") in 2.5 mm (0.1") increments. The set value is displayed in the message area. Select [OK] to return to the main menu. 3-26 User Mode Set Width/Position 5.0 mm Auto set Cent -2.5 mm +2.5 mm set Wide Wide OK Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 65
Mode Output Select the external device connected to the Scanner. Select [Output] from the User Mode menu. The output setting menu appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Select [Printer] when a printer is connected. Select [OK] to return to the main menu. Set - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 66
Exiting User Mode Select [Previous] from the User Mode menu. 3-28 User Mode Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 67
Operation Chapter 3 3-29 Recalling jobs Recall programs registered using [Save Data]. 1 Press the Job Recall key on the control panel. Contrast User Mode Job Recall Mode Check 2 Select anyone of programs No. 1 to 3. The corresponding program is recalled and validated. Select [Previous] to - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 68
. This key can be used to check Contrast settings whenever necessary. User Mode Job Recall Mode Check Current settings are displayed. Select [Next]. ERASE ORIGINAL PRIORITY CONNECTION ON CENTERING OFF OFF OFF Book Auto Quality Next Printer Operation Chapter 3 Select [OK] to return to the - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 69
Expo Zoom A4 Size 1 Out Center Erase (Cent Eras) The shadow generated in the center of the open book is erased during scanning. Spread mode Erasing width Single or Book Split mode Erasing width Operation Chapter 3 Select [Cent Eras]. The menu name is highlighted and the function is activated - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 70
Operation Chapter 3 3-32 Using the edit functions Frame Masking (Masking) Objects outside the original are erased to prevent a shadowed (black) frame from being created on the output, i.e. when the selected paper is larger than the original. Frame Masking: OFF 1 2 1 2 Frame Masking: ON 1 2 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 71
Operation Chapter 3 3-33 Using the edit functions Finger Masking (Fing Mask) This function removes the image of the fingers holding the original from the scanned image. Finger Mask: OFF 1 2 1 2 Finger Mask: ON 1 2 NOTE Finger Masking may affect scanning depending on the density and colors - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 72
Finger Masking is available in the following 2 modes. 3-34 Using the edit functions Masking fingers only 1 2 1 2 Masking outer margins (Including fingers) 1 2 Operation Chapter 3 Default setting is "Masking fingers only." To change the setting, contact your authorized Dealer. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 73
and the scanned image is placed in the center of the paper when printed. 30mm 30mm 1 2 Centering: ON 1 2 Centering: OFF Spread mode 1 2 Single or Book 1 Split mode 2 1 2 NOTE This function is not effective when the center of the original is shifted 30 mm or more from the center of - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 74
3-36 Adjusting exposure for scanning Select [Expo] (exposure) from the main menu to set the exposure for scanning. Print Both Pages A x1.00 A4 1 Edit Expo Zoom Size Out Operation Chapter 3 Auto The appropriate exposure is automatically selected according to the type of original. Select [Auto - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 75
adjustment The exposure for scanning is set manually. Select [Auto] to return the menu name to normal, indicating [Auto] is turned off. "A" disappears from the center of the exposure level bar. Set Exposure - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 76
activated. Select [OK] to return to the main menu. Set Magnification Auto Auto Re x 1.0 Enla duce rge OK NOTE Place only the original on the book table when [Auto] is selected, or the paper size may not be detected. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 77
3-39 Setting magnification Reduce The original is scanned and the image size is reduced. The reduction ratio can be specified by the user. 1 Select [Reduce]. The menu name is highlighted and the reduction setting screen is displayed. Select [OK] to return to the main menu. Set Magnification x 1. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 78
3-40 Setting magnification Full (x 1.0) The original is scanned without changing the size (100%) Select [x 1.0]. The menu name is highlighted. Select [OK] to return to the main menu. Set Magnification x 1.00 Auto Re x 1.0 Enla duce rge OK Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 79
3-41 Setting magnification Enlarge The original is scanned and the image is enlarged. The enlargement ratio can be specified by the user. 1 Select [Enlarge]. The menu name is highlighted and the enlargement setting screen is displayed. Select [OK] to return to the main menu. Set Magnification x - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 80
3 2 Select the appropriate paper size (paper tray or paper cassette) and original direction (portrait or landscape). A3 and A4 paper is set in the printer's cassette and tray respectively in the figure on the right. The selected menu name is highlighted. Select [OK] to return to the main menu. Set - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 81
3-43 Selecting Original Type 1 Select [Out] in the main menu. Print Both Pages A x1.00 A4 1 Edit Expo Zoom Size Out 2 Select [Org. type]. The menu name is highlighted and the original type setting screen is displayed. Set Output Conditions Org. Out Prin type put ts OK Operation Chapter 3 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 82
3-44 Selecting Output Conditions 1 Select [Out] in the main menu. Print Both Pages A x1.00 A4 1 Edit Expo Zoom Size Out 2 Select [Output]. The menu name is highlighted and the priority setting screen is displayed. Set Output Conditions Org. Out Prin type put ts OK Operation Chapter 3 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 83
3-45 Setting the number of copies Sets the number of copies produced. 1 Select [Out] in the main menu. Print Both Pages A x1.00 A4 1 Edit Expo Zoom Size Out Operation Chapter 3 2 Select [Prints]. The menu name is highlighted and the screen for setting the number of copies is displayed. Set - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 84
in Utility Mode: • Initial settings upon power supply • Timers (automatic clear, lamp off, and printer power save) • Warning (detection items and buzzer preferences) • Changing the SCSI port and ID No. Simultaneously press the User Mode key and the Job Recall key on the control panel. Contrast - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 85
If any of the initial settings is changed, turn off the power to the Scanner. Then, turn it on, and the initial settings have been changed accordingly. Utility screen. The initial setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu 2 Select the desired item. The - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 86
for the current and subsequent operations. Select [PC] or [Printer] to connect the scanner to a personal computer or printer respectively. Select [Previous] to return to the previous screen. Select [OK] to define the device to which the Scanner is connected. 3 Select [Reset] to reset all customized - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 87
mode Time Set The settings for the timer (automatic clear time, lamp off time, and printer power save time) are set. 1 Select [Time set] on the main Utility screen. The timer setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu Operation Chapter 3 2 Select the - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 88
been pressed. Select [1 min.], [3 min.], or [5 min.] to set the desired lamp off time. Select [OK] to define the setting. 3 Select [Save mode] to set the time -3 until the printer enters Sleep mode after printing has been completed (printer power save time). Select [10 min.], [20 min.], or [30 min - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 89
defined here become effective immediately. 1 Select [Caution] on the main Utility screen. The warning setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu Operation Chapter 3 2 Select the desired item. The selected menu name is highlighted. Select [Previous] to - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 90
3 Select [Buzzer] to set when the -2 buzzer goes off. Selecting [Alarm] makes the buzzer go off only when any warning message appears. Selecting [Stop] makes the buzzer go off when any prohibited operation is attempted, as well as when any warning message appears. Selecting [Key in] makes the buzzer - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 91
Up ID=2 Prev ious OK NOTE Do not set any ID number which has already been used for other SCSI unit. If any of the SCSI ID numbers is changed, turn off the powers to the Scanner and the connected PC. Then, turn them on, and the ID numbers have been changed accordingly. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 92
Exiting Utility mode Select [Main Menu] on the main Utility screen. 3-54 Operations in Utility mode Select Function Init Time Caut SCSI Main ial set ion set Menu Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 93
3-55 Operations in Utility mode Operation Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 94
Printer Chapter 4 Chapter 4 Printer - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 95
: Power Switch: Use to open the Upper Unit. Light indicates when the Printer is turned ON. Prints are output from the Printer, face down onto this tray which can hold up to 500 sheets of standard paper. Slide the guides to secure the paper stack. Capable of holding up to 150 sheets of - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 96
: Permanently fixes the image onto the sheet of paper. Interface Connectors: Facilitates connections for the Scanner. * The Printer has two connectors to facilitate connection with two separate Scanner units. Imaging Cartridge: Where the image is generated for transfer onto the sheet of paper. Be - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 97
4-3 Troubleshooting and Maintenance Replenishing the Paper Supply Use only the following types of paper: Type Plain and paper Up to 250 sheets Loading Paper into the Paper Feeding Tray 1 Swing down the Paper Feeding Tray. Printer Chapter 4 2 Fan the paper stack thoroughly and align the edges. - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 98
Paper Guides to secure the paper stack. 4-4 Troubleshooting and Maintenance CAUTION Make sure that the paper stack does not exceed the Maximum Level Indicator. Load a new paper stack only after the old one has run out. Paper can be set only in the crosswise direction. Printer - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 99
Printer Chapter 4 4-5 Troubleshooting and Maintenance Loading Paper in the Paper Cassette 1 Pull the cassette out of the Printer and open the Cover. 2 Press down the Paper Lifting Plate until it locks. Fan the paper stack thoroughly, align the edges, and place the paper - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 100
5 Close the Cover and insert the cassette into the Printer. 4-6 Troubleshooting and Maintenance Printer Chapter 4 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 101
4-7 Troubleshooting and Maintenance Replacing the Toner Cartridge 1 Open the upper unit by pulling the Upper Unit Lock Release Lever forward. 2 Remove the old Imaging Cartridge from the printer. 3 Take a new Imaging Cartridge out of the box. Holding it with both hands, shake it well in the - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 102
the seal from the Imaging Cartridge by pulling it steadily straight out. 4-8 Troubleshooting and Maintenance 5 Shake the Imaging Cartridge four or five more times as shown to evenly distribute the toner inside. Printer Chapter 4 6 Slide the pins located on both sides of the Imaging Cartridge - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 103
4-9 Troubleshooting and Maintenance 7 Close the Upper Unit. NOTE Push the Print Tray in before opening the Upper Unit. Printer Chapter 4 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 104
4-10 Troubleshooting and Maintenance Clearing Misfeeds A misfeed has occurred in the Printer. Clear the sheet of misfed paper by following the procedure given below. CAUTION The Fusing Unit inside the printer becomes very hot during operation. To avoid a burn, be very careful not to touch it. 1 Open - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 105
Printer Chapter 4 4-11 Troubleshooting and Maintenance 3 Remove the sheet of paper. Clearing a Remove the sheet(s) of paper that caused the misfeed as shown. Clearing a Misfeed from inside the Printer If the misfeed occurred before the sheet of paper entered the Fusing Unit, gently pull the misfed - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 106
4-12 Troubleshooting and Maintenance NOTE • Since the toner has not yet been fixed onto the sheet of paper, be careful not to paper toward the output end of the Fusing Unit as shown. 4 Check that no misfed paper is left in the Printer and then reinstall the Imaging Cartridge. 5 Close the Upper Unit - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 107
Troubleshooting and Maintenance Solving Irregular Printing Problems Use the following procedures to fix minor printing problems image Print density is not properly Change the print density set. setting as necessary. Printer Chapter 4 ABCDE F ABCDE F ABCDE F ABCDE F ABCDE F Partial void image - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 108
4-14 Troubleshooting and Maintenance Symptom Uneven image density Cause Action Toner in the Imaging Car- Remove the Imaging Car- tridge is not evenly distrib- tridge, shake it several uted. times and replace. A BCDE F A BCDE F A BCDE F A BCDE F A BCDE F Blank print The Printer has malfunc- - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 109
Printer Chapter 4 4-15 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 110
Chapter 5 Troubleshooting Troubleshooting Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 111
problem. Warning message When any error occurs in parameters for auto focus, auto exposure, or paper size detection prior to scanning, a warning message appears on the display and the Scanner letter "C") and call your authorized dealer. Service Call Call Tech. Rep C15XX Troubleshooting Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 112
surface is within the range 65 mm above the book table. • Select Sheet mode. • The steel mirror is dirty. • Clean the steel mirror. • Light from the room lighting or the outside through windows reflects on the steel mirror. • Relocate the Scanner to a place where light from the room lighting or - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 113
the start switch is pressed. • An obstacle is blocking the lamp. • Remove the obstacle blocking the lamp. Printer is OFF Turn Printer ON • The printer is not turned on. • The printer is disconnected. • Turn the printer on. • Connect the printer. Paper Jam Remove Paper on Drum (in Take Up, in - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 114
5-4 Troubleshooting warning messages Warning message Start Appli./Driver Possible cause • Current [Output] setting is [PC] connection. Action • Change the [Output] setting to [Printer]. Troubleshooting Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 115
5-5 Troubleshooting warning messages Troubleshooting Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 116
Chapter 6 Maintenance Maintenance Chapter 6 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 117
checks 1. Any of the following conditions could damage the Scanner or other electrical equipment. Move the Scanner immediately and eliminate the possible cause of malfunction. • The Scanner is placed on the power cord or other cables. • The Scanner is placed on any cord of other electrical devices - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 118
6-2 Maintenance Cleaning the MSP 3000 Printer Clean the Printer at regular intervals. NOTE • Before cleaning the Printer, turn OFF the power and unplug the cord from the power outlet. • Use a soft cloth and NEVER use abrasives or corrosive detergents. Exterior Panels 1 Clean - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 119
Maintenance Chapter 6 6-3 Maintenance - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 120
Chapter 7 Specifications Specifications Chapter 7 - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 121
correction: Text/Photo mode: Finger mask: Desk-top book scanner for face-up originals Rotary mirror scanning system Book, Sheet Max. 432 mm x 594 mm (Scanning (7500 pixels) Long cylindrical halogen lamp (DC150V, 620 W) Automatic (9 steps) or Manual (9 steps) Automatic or Manual (0-50 mm or 0-2") - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 122
or 22" (W) x 20-1/2" (D) x 16" (H) Scanner: 64 kg(140 lbs), Printer: 28kg (61-3/4lbs.) 120 V, 60Hz/ 220-240V, 50-60Hz Scanner: Less than 1000 W, Printer: Less than 750 W Standby-state:30 dB or less, Operation:62 dB or less Video I/F (Printer), SCSI-2 (PC) Angle Book Holder, PC Interface Kit, Foot - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 123
For Key Operator's Use When you need to call for service, the Key Operator should be prepared to provide the following (s) on the Display. etc. For your reference purpose. Model Name Printer Name PS7000 MSP 3000 Printer Serial No. Serial No. Installation Data Authorized Dealer's Name TEL. No - Konica Minolta PS7000 | PS7000 Operator Manual (Printer Version) - Page 124
CO., LTD Printed in Japan The information contained in this manual is subject to change without notice to incorporate improvements made on the product or products the manual covers. MINOLTA CO., LTD. Image Information Products Marketing Headquarters 3-13, 2-chome, Azuchi-machi, Chuo-ku, Osaka
OperatorĀ“s Manual
PS7000
0818-7704-13
PR version