Konica Minolta bizhub PRESS C71hc bizhub PRESS C1060/C1070/C1070P/PRO C1060L D - Page 32

Output about 3 sheets of the same job data that you output in step 1 from the same

Get Konica Minolta bizhub PRESS C71hc PDF manuals and user guides View all Konica Minolta bizhub PRESS C71hc manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

13 Check the position difference of the back side among the back side images of the + second and third output that were output after the magnification adjustment is completed. The black line in the figure shows the back side, - + and the blue dashed line shows the other side (front side). When the position of the front side image and the back side image differs, input the adjustment value in [Up/Down] (crosswise direction) and [Right/Left] (paper feed direction). To move the image up or to the right, enter the value with a positive mark (+). To move the image down or to the left, enter the value with a negative mark (-). back Example of adjusting the image position: When the back side is misaligned to the front side by 0.5 mm down and 0.3 mm to the right, enter [+0.5 mm] in [Up/Down], and [-0.3 mm] in [Right/Left]. Tips - The adjustment value changes 0.1 mm on a 1-step basis. - Adjustment range: [Up/Down] -10.0 to +10.0, [Right/Left] -3.0 to +3.0 14 After the adjustment is completed, press [OK]. 15 Output about 3 sheets of the same job data that you output in step 1 from the same tray. 16 Check the image position difference of the back side of the jobs that are output as the second and third sheet. Repeat from step 13 to step 15 until all image position difference are cleared. When all image position difference are cleared, exit the adjustment. 2-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
2-21
13
Check the position difference of the back
side among the back side images of the
second and third output that were output
after the magnification adjustment is
completed.
The black line in the figure shows the back side,
and the blue dashed line shows the other side
(front side).
When the position of the front side image and the
back side image differs, input the adjustment
value in [Up/Down] (crosswise direction) and
[Right/Left] (paper feed direction).
To move the image up or to the right, enter the
value with a positive mark (+). To move the image
down or to the left, enter the value with a negative
mark (–).
Example of adjusting the image position:
When the back side is misaligned to the front side
by 0.5 mm down and 0.3 mm to the right, enter
[+0.5 mm] in [Up/Down], and [-0.3 mm] in
[Right/Left].
Tips
-
The adjustment value changes 0.1 mm on a 1-step
basis.
-
Adjustment range: [Up/Down] –10.0 to +10.0,
[Right/Left] –3.0 to +3.0
14
After the adjustment is completed, press
[OK].
15
Output about 3 sheets of the same job data that you output in step 1 from the same
tray.
16
Check the image position difference of the back side of the jobs that are output as the
second and third sheet.
Repeat from step 13 to step 15 until all image position difference are cleared.
When all image position difference are cleared, exit the adjustment.
back
+
+
-
-