Konica Minolta bizhub PRESS C71hc bizhub PRESS C1060/C1070/C1070P/PRO C1060L D - Page 81

The calibration table is registered in the image

Get Konica Minolta bizhub PRESS C71hc PDF manuals and user guides View all Konica Minolta bizhub PRESS C71hc manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

12 Click [Next] and perform the rest of the measurement by following the instructions on the screen. Perform the rest of the measurement with the same procedures, in order of "2. The 1st enhancement of a correction table (FB1)", "3. The 2nd enhancement of a correction table (FB2)", "4. The 3rd enhancement of a correction table (FB3)", and "5. The accuracy measurement of FB3". 13 After the measurement of the "5. The accuracy measurement of FB3", click [OK] on [Operation steps] screen. bizhub PRESS C1070/C1070P/C1060 bizhub PRO C1060L 14 Change the measurement number on the right side of [Select] and check the ['E Ave], ['E Max] values, and the ['a] ['b] graph of the Gray displayed within the [Gray Step] frame. As for the Gray, check the information within the [Gray Step] frame and select the calibration data that has the smallest difference from the target. Then click [Register the selected result.] . Tips - When you put a priority on the gray reproducibility of the low density, check the left half of the ['a] ['b] graph that is displayed within the [Gray Step] frame. And select the calibration data that ['a] and ['b] values are close to "0". - When you put a priority on the gray reproducibility of the high density, check the right half of the ['a] ['b] graph that is displayed within the [Gray Step] frame. And select the calibration data that ['a] and ['b] values are close to "0". 15 Click [OK] on the [Information] screen. The calibration table is registered in the image controller. 3 3-49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
3-49
bizhub PRO C1060L
bizhub PRESS C1070/C1070P/C1060
3
12
Click [Next] and perform the rest of the
measurement by following the
instructions on the screen.
Perform the rest of the measurement with the
same procedures, in order of "2. The 1st
enhancement of a correction table (FB1)", "3. The
2nd enhancement of a correction table (FB2)", "4.
The 3rd enhancement of a correction table (FB3)",
and "5. The accuracy measurement of FB3".
13
After the measurement of the "5. The
accuracy measurement of FB3", click
[OK] on [Operation steps] screen.
14
Change the measurement number on the
right side of [Select] and check the [
'
E
Ave], [
'
E Max] values, and the [
'
a] [
'
b]
graph of the Gray displayed within the
[Gray Step] frame.
As for the Gray, check the information
within the [Gray Step] frame and select
the calibration data that has the smallest
difference from the target. Then click
[Register the selected result.] .
Tips
-
When you put a priority on the gray reproducibility of
the low density, check the left half of the [
'
a] [
'
b]
graph that is displayed within the [Gray Step] frame.
And select the calibration data that
[
'
a] and [
'
b]
values are close to "0".
-
When you put a priority on the gray reproducibility of
the high density, check the right half of the [
'
a] [
'
b]
graph that is displayed within the [Gray Step] frame.
And select the calibration data that
[
'
a] and [
'
b]
values are close to "0".
15
Click [OK] on the [Information] screen.
The calibration table is registered in the image
controller.