Konica Minolta bizhub PRO 1100 bizhub PRO 1100 Daily Maintenance Guide - Page 58

Select [Gap], then press [Print Mode].

Get Konica Minolta bizhub PRO 1100 PDF manuals and user guides View all Konica Minolta bizhub PRO 1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

4 Select [Gap], then press [Print Mode]. 5 When the [PRINT MODE] screen is displayed, press Start on the control panel. A test chart is printed out. 6 Press [Exit Print Mode]. 7 Measure the gap between the front and back sides at each point of [a] to [d] on the [back] side of the printed out chart. [a] - This figure shows an example to measure [a]. The scale resolution is 0.5 mm. back - In this figure, the black line indicates the front side, and the blue line indicates the back side. - The measurement value can be entered in - units of up to 0.1 mm. - For example, as shown in the figure, if the scale of [a] is misaligned 1.5 mm in the plus side compared with the front side, press [1] - [5] - [+/-] to enter "-1.5" as the adjustment value. Then, the blue line on the back side will be moved 1.5 mm toward the minus side. - Write down the measured values so that you do not forget them. 2-32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
2-32
4
Select [Gap], then press [Print Mode].
5
When the [PRINT MODE] screen is
displayed, press
Start
on the
control
panel
.
A test chart is printed out.
6
Press [Exit Print Mode].
7
Measure the gap between the front and
back sides at each point of [a] to [d] on
the [back] side of the printed out chart.
-
This figure shows an example to measure [a].
The scale resolution is 0.5 mm.
-
In this figure, the black line indicates the front
side, and the blue line indicates the back side.
-
The measurement value can be entered in
-
units of up to 0.1 mm.
-
For example, as shown in the figure, if the
scale of [a] is misaligned 1.5 mm in the plus
side compared with the front side, press [1] -
[5] - [+/-] to enter "-1.5" as the adjustment
value. Then, the blue line on the back side will
be moved 1.5 mm toward the minus side.
-
Write down the measured values so that you
do not forget them.
back
[a]