Lenovo ThinkCentre A58e Hardware Maintenance Manual - Page 60

Check AC/DC power adapter, SCSI interface Test Passed

Get Lenovo ThinkCentre A58e PDF manuals and user guides View all Lenovo ThinkCentre A58e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Diagnostic error code 025-196-XXX IDE interface test halt, error threshold exceeded 025-197-XXX IDE interface test warning 025-198-XXX IDE interface test aborted 025-199-XXX IDE interface test failed, cause unknown 030-000-XXX SCSI interface Test Passed 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface configuration/setup error 030-03X-XXX 030-04X-XXX SCSI interface error 030-195-XXX SCSI interface test aborted by user 030-196-XXX SCSI interface test halt, error threshold exceeded FRU/Action 1. Press F3 to review the log file 2. Re-start the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility" on page 41 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility" on page 41 2. Flash the system and re-test. See "Updating (flashing) BIOS from a disc" on page 99 3. Go to "Undetermined problems" on page 64 1. Go to "Undetermined problems" on page 64 2. Flash the system and re-test. See "Updating (flashing) BIOS from a disc" on page 99 3. Replace component under function test No action 1. SCSI signal cable 2. Check AC/DC power adapter 3. SCSI device 4. SCSI adapter card, if installed 5. System board 1. SCSI signal cable 2. Flash the system. See "Updating (flashing) BIOS from a disc" on page 99 3. SCSI device 4. SCSI adapter card, if installed 5. System board 1. SCSI signal cable 2. Check AC/DC power adapter 3. SCSI device 4. SCSI adapter card, if installed 5. System board Information only Re-start the test, if necessary 1. Press F3 to review the log file 2. Re-start the test to reset the log file 54 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Diagnostic error code
FRU/Action
025-196-XXX
IDE interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
025-197-XXX
IDE interface test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using the
Setup Utility” on page 41
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
025-198-XXX
IDE interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled. See Chapter 6 “Using the
Setup Utility” on page 41
2. Flash the system and re-test. See “Updating
(flashing) BIOS from a disc” on page 99
3. Go to “Undetermined problems” on page 64
025-199-XXX
IDE interface test failed, cause unknown
1. Go to “Undetermined problems” on page 64
2. Flash the system and re-test. See “Updating
(flashing) BIOS from a disc” on page 99
3. Replace component under function test
030-000-XXX
SCSI interface Test Passed
No action
030-00X-XXX 030-01X-XXX
SCSI interface failure
1. SCSI signal cable
2. Check AC/DC power adapter
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-027-XXX
SCSI interface configuration/setup error
1. SCSI signal cable
2. Flash the system. See “Updating (flashing) BIOS
from a disc” on page 99
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-03X-XXX 030-04X-XXX
SCSI interface error
1. SCSI signal cable
2. Check AC/DC power adapter
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-195-XXX
SCSI interface test aborted by user
Information only Re-start the test, if necessary
030-196-XXX
SCSI interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
54
Hardware Maintenance Manual