Lexmark 7675 User's Guide - Page 140

Can receive but not send faxes, Fax Setup, Dialing and Sending, Dial Prefix, Create, Dial Method

Page 140 highlights

Can receive but not send faxes These are possible solutions. Try one or more of the following: CHECK MODE SELECTION To make sure that the printer is set for faxing, check to see if the If the light is not on, press on the printer control panel. light is on. CHECK DOCUMENT PLACEMENT Load the original document faceup in the Automatic Document Feeder (ADF) or facedown in the upper left corner of the scanner glass. CHECK THE DIAL PREFIX SETTING 1 From the printer control panel, press . 2 Press the up or down arrow button until Fax Setup is highlighted, and then press OK. 3 Press the up or down arrow button until Dialing and Sending is highlighted, and then press OK. 4 Press the up or down arrow button until Dial Prefix is highlighted, and then press OK. 5 To change the setting, press the up or down arrow button until Create is highlighted, and then press OK. 6 Using the keypad, enter the prefix to be dialed before each telephone number, and then press OK to save the setting. CHECK SPEED DIAL NUMBER • Check to make sure Speed Dial has been programmed for the number that you want to dial. For more information, see the instructions for setting up Speed Dial. • As an alternative, dial the telephone number manually. MAKE SURE THE PRINTER DETECTS DIAL TONE • See the instructions for sending a fax while listening to a call (on hook dial). • Check the Dial Method setting. 1 Listen for a dial tone. If you hear a dial tone but the printer hangs up without dialing, this means it did not recognize the dial tone. 2 From the printer control panel, press . 3 Press the up or down arrow button until Fax Setup is highlighted, and then press OK. 4 Press the up or down arrow button until Dialing and Sending is highlighted, and then press OK. 5 Press the up or down arrow button until Dial Method is highlighted, and then press OK. 6 Press the up or down arrow button until Behind PBX (Dial Tone Detect Off) is highlighted, and then press OK to save the setting. Troubleshooting 140

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181

Can receive but not send faxes
These are possible solutions. Try one or more of the following:
C
HECK
MODE
SELECTION
To make sure that the printer is set for faxing, check to see if the
light is on.
If the
light is not on, press
on the printer control panel.
C
HECK
DOCUMENT
PLACEMENT
Load the original document faceup in the Automatic Document Feeder (ADF) or facedown in the upper left corner
of the scanner glass.
C
HECK
THE
D
IAL
P
REFIX
SETTING
1
From the printer control panel, press
.
2
Press the up or down arrow button until
Fax Setup
is highlighted, and then press
OK
.
3
Press the up or down arrow button until
Dialing and Sending
is highlighted, and then press
OK
.
4
Press the up or down arrow button until
Dial Prefix
is highlighted, and then press
OK
.
5
To change the setting, press the up or down arrow button until
Create
is highlighted, and then press
OK
.
6
Using the keypad, enter the prefix to be dialed before each telephone number, and then press
OK
to save the
setting.
C
HECK
S
PEED
D
IAL
NUMBER
Check to make sure Speed Dial has been programmed for the number that you want to dial. For more
information, see the instructions for setting up Speed Dial.
As an alternative, dial the telephone number manually.
M
AKE
SURE
THE
PRINTER
DETECTS
DIAL
TONE
See the instructions for sending a fax while listening to a call (on hook dial).
Check the Dial Method setting.
1
Listen for a dial tone. If you hear a dial tone but the printer hangs up without dialing, this means it did not
recognize the dial tone.
2
From the printer control panel, press
.
3
Press the up or down arrow button until
Fax Setup
is highlighted, and then press
OK
.
4
Press the up or down arrow button until
Dialing and Sending
is highlighted, and then press
OK
.
5
Press the up or down arrow button until
Dial Method
is highlighted, and then press
OK
.
6
Press the up or down arrow button until
Behind PBX (Dial Tone Detect Off)
is highlighted,
and then press
OK
to save the setting.
Troubleshooting
140