Home » LiftMaster Manuals » Garage Door Openers » LiftMaster EL2000 » Manual Viewer

LiftMaster EL2000 EL25-KEYPAD PROGRAMMING Manual - Page 21

Programming Multiple Units Overview, Verify Unit Number: 111 - telephone entry system

View all LiftMaster EL2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Programming Multiple Units Overview Programming Multiple Units Overview Programming Multiple Units Overview Up to seven (7) units can be installed on a single telephone line. Each unit must have a "Unique Unit ID" number and the "Number of Units in Chain" assigned to it. Set the Unit ID Number and Number of Units in Chain: 2 The unit ID identifies each unit within a chain. Adding or removing will require the unit ID's to be re-entered. Factory Setting: Unit ID 1 and Number of Units in Chain 1. 1 Press Then 2 Unit ID Number (1-7), Then 3 Total Number of Units in Chain (1-7), Then Important: This must be performed for EACH unit in the Chain Example: Unit ID "1" AUG 10, 2005 WELCOME Unique Unit ID Sequencial Order Unit ID "2" AUG 10, 2005 WELCOME Unit ID "3" AUG 10, 2005 WELCOME Unit ID "7" AUG 10, 2005 WELCOME Telco Entrance Box Demarcation Point Residence Number of Units in Chain "7" Important: You must program each unit ID using the main keypad first before attempting remote access. EACH unit in the Chain must have the same "Rings Before Answer" 16 . Factory Setting - 5 Rings EACH unit in the Chain must have the same "Alternate Prefix" 115 . Factory Setting - Normal (use to enter programming) Be sure to set the rings before answer value 16 is greater than maximum rings before aborting attempt 14 . Verify Unit Number: 111 This allows you to verify a unit's number within a chain. When you perform this step, the unit will respond with the number corresponding to its unit ID number. The message two (2), for example, means the unit is number 2 in the chain. Then If you make an error during an entry, press the asterisk key (*) to begin again. Page 20

Section	Page
Keypad Programmiing Manual for EL Models	1
Keypad Programming Guide	2
Table of Contents	3
Table of Contents Continued	4
Quick Reference Guide for Keypad Programming the Units	5
Quick Reference Continued	6
Quick Reference Continued	7
Quick Reference Continued	8
Quick Reference Continued	9
Introduction	10
Multi-Resident Complex (Dial-Out)	10
Multi-Resident Complex (Manager Sharing)	11
NPB Multi-Resident Complex	11
Single Family Residence (NPB) Example	12
Multi-Resident Complex Example	13
Your System Layout	14
Programming Single Unit Overview	15
Programming Basics	15
Procedure Required to Program EL Models:	16
Enter Programming Mode	17
Exit Programming Mode	17
System Feedback / Responses (Beeps)	18
Other Response:	18
Visual Responses:	18
Direct Command Responses:	19
Visitor Responses:	19
Sending Direct Commands from the Resident’s Phone	20
Programming Multiple Units Overview	21
Verify Unit Number: 111	21
Setup “Your Settings”	22
Change the Unit’s ID and Chain Number for Multiple Unit Configurations ONLY: 2	22
Setup External Access Control Devices	23
What is a Relay?	23
Configuring \	24
Step 1 Set Each \	24
Step 2 Set Each Relay’s \	24
Step 3 Assign \	25
Step 4 Assign Each External Access Control Device a \	25
\	26
Unit Controlling 1 Door	27
Unit Controlling 2 Doors and Vehicle Gate	27
Unit Controlling 4 Doors	28
Directory Codes	29
Set Directory Code Length	30
Add, Edit or Delete Directory Codes	30
Add Basic Directory Code: 40	30
Add or Edit Full Function Directory Code: 41	31
Change a Directory Code ONLY: 44	31
Delete a Directory Code: 48	31
Delete ALL Directory Codes: 201	32
Enable or Disable Do Not Disturb Schedule	32
Enable or Disable Call Forwarding (Directory Calls)	32
Add / Modify Resident DnD and/or Call Forwarding	33
Activate or Deactivate a Directory Code	33
Directory Code Display Option	34
Resident Display Option	34
Entry Codes	35
Set an Entry Code Length	36
Add, Edit or Delete Entry Codes	36
Add a Basic Entry Code: 50	36
Add or Edit Full Function Entry Code: 51	37
Change Entry Code ONLY: 54	37
Delete an Entry Code: 57	37
Change Entry Code Door Access: 75	37
Assign Utility Option: 58	38
Assign Special Use Entry Code at the Unit Keypad: 59	38
Delete ALL Entry Codes: 202	39
Activate or Deactivate an Entry Code	39
Verify an Entry Code	39
Access Cards	40
Add, Edit or Delete Cards	41
Add a Basic Card: 80	41
Add or Edit a Full Function Card: 81	42
Add a Group of Cards at Once: 82	42
Delete a Card: 88	43
Delete ALL Cards: 203	43
Activate or Deactivate a Card	43
Verify a Card	44
Facility Codes	44
Card Types	44
Transmitters	45
Add, Edit or Delete Transmitter	46
Add a Basic Transmitter: 90	46
Add or Edit a Full Function Transmitter: 91	47
Add or Edit a Group of Full Function Transmitters: 94	47
Delete a Transmitter: 100	48
Delete ALL Transmitters: 204	48
Activate or Deactivate a Transmitter	49
Verify a Transmitter	49
Time Zones, Holidays and Clock	50
Creating Time Zones	51
Setting Holidays	51
Assigning Door Use and Unlock Time Zone	52
Enable or Disable Unlock Schedule: 11	52
Assign Door Auto Lock / Unlock Schedule: 31	52
Deleting ALL Time Zones	53
Setting the Clock	53
Enable or Disable Daylight Saving Time: 4	53
Features	54
Set Anti-Passback Entry/Exit for Specific Devices: 64	54
Set Anti-Passback Time: 13	54
Enable or Disable Anti-Passback Forgiveness at Midnight: 105	55
Enable or Disable Utility Option: 58	55
Configure the Alarm Features	55
Configure “Door Forced Open” Alarm Feature: 103	56
Setting “Strikes and Out” (Number of Entry Code Attempts before Disabling Unit): 17	56
Configure “Strikes and Out” Alarm Feature: 104	56
Change or Verify the Unit’s Password	57
Communications To and From Unit	58
Number of Rings Before Unit Answers: 16	59
Override Telephone Company Answering Service: 109	59
Enable or Disable Telco Mode: 20	59
Dial \	59
Set a Phone Number’s Extension Delay Time: 110	60
Speaker / Microphone Settings	60
Enable or Disable Call Waiting	60
Visitor Communication Settings	61
Set Visitor Talk Time: 5	62
Enable or Disable “Announce All Doors/Access Granted” 26	62
Set Display Greeting: 160	62
Return to Menu Programming: 25	62
LCD Visitor Messages	63
LCD Visitor Messages (continued)	64
Postal Lock/Autocall/Exit/Door Sensor Devices	65
Autocall Device	65
Request to Exit Device (REX)	66
Door Sensing Devices	67
Direct Commands From The Phone	68
Speaking Through the Unit (Intercom Mode): 120	68
Direct Commands from Your Phone: 120 121 122	69
Direct Commands from Your Phone (continued): 123 124 125 126	70
Real-Time Monitoring	71
Reset/Restore the Unit and Database	72
Reset the Unit: 29	72
Delete ALL Access Codes from Database: 206	72
Keypad Template	73
Notes	74
Glossary	76
Glossary Continued	77
Appendix	78