Home » LiftMaster Manuals » Garage Door Openers » LiftMaster EL2000 » Manual Viewer

LiftMaster EL2000 EL25-KEYPAD PROGRAMMING Manual - Page 59

Number of Rings Before Unit Answers: 16, Override Telephone Company Answering Service: 109

View all LiftMaster EL2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Number of Rings Before Unit Answers: 16 When someone remotely calls the unit for programming, the unit answers the call after a configurable number of rings. Factory Setting: 5 Rings 1 Press Then 2 Enter Number of Rings (0 to 15). Then (#) Example: "0" disables the unit and no incoming calls will be answered. It will NOT be able to be remotely programmed. 1 2 Unit will Answer a Remote Call after 7 Rings NOTE: If you have an answering machine (or answering service) attached to the same phone line as the unit, set the unit count for two (2) or more rings higher than the answering machine/service count. See also Override Telephone Company Answering Service (See Below). Override Telephone Company Answering Service: 109 Communications To and From Unit Communications To and From Unit You can override an answering service by dialing the line attached to your unit, letting the phone ring only once or twice, then hang up. After a few seconds, dial the same number again. The unit will immediately answer the second call. If you do not call back within 60 seconds, this feature will reset and you must start over. Factory Setting: Disabled 1 Press Then Example: 2 Enable (1) or Disable (0). Then (#) 1 2 Override is enabled. The unit will answer the second call after a few number of rings, hang up and callback is performed. Enable or Disable Telco Mode: 20 Telco mode is using the main telephone line for the unit's communications to a house or complex. Enable the Telco mode if the unit will use a regular telephone line. Disable the Telco mode if the unit will not have a regular telephone line connected to it. If the Telco mode is disabled and the unit is connected to a regular telephone line, it will ignore all Telco features (call forwarding, call waiting, etc.). Factory Setting: Enabled 1 Press Then Example: 2 Enable (1) or Disable (0). Then (#) 1 2 Telco mode is disabled. 113 Dial "0-9" First to Get an Outside Line Using an Automated Phone System: When the unit is connected to a PBX telephone system (Automated), it can be programmed to dial a specific PBX number (0-9) then pause briefly, allowing the PBX system to give the unit an outside line. Factory Setting: Disabled 1 Press Then 3 Enter Specific PBX Digit (0-9). Then (#) 2 Enable (1) or Disable (0). Then (#) Example: 1 2 3 Enables Unit to dial "9 and Pause" to connect to an outside line. Page 58

Section	Page
Keypad Programmiing Manual for EL Models	1
Keypad Programming Guide	2
Table of Contents	3
Table of Contents Continued	4
Quick Reference Guide for Keypad Programming the Units	5
Quick Reference Continued	6
Quick Reference Continued	7
Quick Reference Continued	8
Quick Reference Continued	9
Introduction	10
Multi-Resident Complex (Dial-Out)	10
Multi-Resident Complex (Manager Sharing)	11
NPB Multi-Resident Complex	11
Single Family Residence (NPB) Example	12
Multi-Resident Complex Example	13
Your System Layout	14
Programming Single Unit Overview	15
Programming Basics	15
Procedure Required to Program EL Models:	16
Enter Programming Mode	17
Exit Programming Mode	17
System Feedback / Responses (Beeps)	18
Other Response:	18
Visual Responses:	18
Direct Command Responses:	19
Visitor Responses:	19
Sending Direct Commands from the Resident’s Phone	20
Programming Multiple Units Overview	21
Verify Unit Number: 111	21
Setup “Your Settings”	22
Change the Unit’s ID and Chain Number for Multiple Unit Configurations ONLY: 2	22
Setup External Access Control Devices	23
What is a Relay?	23
Configuring \	24
Step 1 Set Each \	24
Step 2 Set Each Relay’s \	24
Step 3 Assign \	25
Step 4 Assign Each External Access Control Device a \	25
\	26
Unit Controlling 1 Door	27
Unit Controlling 2 Doors and Vehicle Gate	27
Unit Controlling 4 Doors	28
Directory Codes	29
Set Directory Code Length	30
Add, Edit or Delete Directory Codes	30
Add Basic Directory Code: 40	30
Add or Edit Full Function Directory Code: 41	31
Change a Directory Code ONLY: 44	31
Delete a Directory Code: 48	31
Delete ALL Directory Codes: 201	32
Enable or Disable Do Not Disturb Schedule	32
Enable or Disable Call Forwarding (Directory Calls)	32
Add / Modify Resident DnD and/or Call Forwarding	33
Activate or Deactivate a Directory Code	33
Directory Code Display Option	34
Resident Display Option	34
Entry Codes	35
Set an Entry Code Length	36
Add, Edit or Delete Entry Codes	36
Add a Basic Entry Code: 50	36
Add or Edit Full Function Entry Code: 51	37
Change Entry Code ONLY: 54	37
Delete an Entry Code: 57	37
Change Entry Code Door Access: 75	37
Assign Utility Option: 58	38
Assign Special Use Entry Code at the Unit Keypad: 59	38
Delete ALL Entry Codes: 202	39
Activate or Deactivate an Entry Code	39
Verify an Entry Code	39
Access Cards	40
Add, Edit or Delete Cards	41
Add a Basic Card: 80	41
Add or Edit a Full Function Card: 81	42
Add a Group of Cards at Once: 82	42
Delete a Card: 88	43
Delete ALL Cards: 203	43
Activate or Deactivate a Card	43
Verify a Card	44
Facility Codes	44
Card Types	44
Transmitters	45
Add, Edit or Delete Transmitter	46
Add a Basic Transmitter: 90	46
Add or Edit a Full Function Transmitter: 91	47
Add or Edit a Group of Full Function Transmitters: 94	47
Delete a Transmitter: 100	48
Delete ALL Transmitters: 204	48
Activate or Deactivate a Transmitter	49
Verify a Transmitter	49
Time Zones, Holidays and Clock	50
Creating Time Zones	51
Setting Holidays	51
Assigning Door Use and Unlock Time Zone	52
Enable or Disable Unlock Schedule: 11	52
Assign Door Auto Lock / Unlock Schedule: 31	52
Deleting ALL Time Zones	53
Setting the Clock	53
Enable or Disable Daylight Saving Time: 4	53
Features	54
Set Anti-Passback Entry/Exit for Specific Devices: 64	54
Set Anti-Passback Time: 13	54
Enable or Disable Anti-Passback Forgiveness at Midnight: 105	55
Enable or Disable Utility Option: 58	55
Configure the Alarm Features	55
Configure “Door Forced Open” Alarm Feature: 103	56
Setting “Strikes and Out” (Number of Entry Code Attempts before Disabling Unit): 17	56
Configure “Strikes and Out” Alarm Feature: 104	56
Change or Verify the Unit’s Password	57
Communications To and From Unit	58
Number of Rings Before Unit Answers: 16	59
Override Telephone Company Answering Service: 109	59
Enable or Disable Telco Mode: 20	59
Dial \	59
Set a Phone Number’s Extension Delay Time: 110	60
Speaker / Microphone Settings	60
Enable or Disable Call Waiting	60
Visitor Communication Settings	61
Set Visitor Talk Time: 5	62
Enable or Disable “Announce All Doors/Access Granted” 26	62
Set Display Greeting: 160	62
Return to Menu Programming: 25	62
LCD Visitor Messages	63
LCD Visitor Messages (continued)	64
Postal Lock/Autocall/Exit/Door Sensor Devices	65
Autocall Device	65
Request to Exit Device (REX)	66
Door Sensing Devices	67
Direct Commands From The Phone	68
Speaking Through the Unit (Intercom Mode): 120	68
Direct Commands from Your Phone: 120 121 122	69
Direct Commands from Your Phone (continued): 123 124 125 126	70
Real-Time Monitoring	71
Reset/Restore the Unit and Database	72
Reset the Unit: 29	72
Delete ALL Access Codes from Database: 206	72
Keypad Template	73
Notes	74
Glossary	76
Glossary Continued	77
Appendix	78

Match case Limit results 1 per page

Page 58

Communications To and From Unit

Number of Rings Before Unit Answers:

Override Telephone Company Answering Service:

Press

Then

Enable (1) or Disable (0). Then (#)

You can override an answering service by dialing the line attached to your unit, letting the

phone ring only once or twice, then hang up. After a few seconds, dial the same number

again. The unit will immediately answer the second call. If you do not call back within 60

seconds, this feature will reset and you must start over.

Factory Setting: Disabled

Example:

Press

Then

Enter Number of Rings (0 to 15). Then (#)

When someone remotely calls the unit for programming, the unit answers the call after a

configurable number of rings.

Factory Setting: 5 Rings

"0"

disables the unit and no incoming

calls will be answered. It will

NOT

be able

to be remotely programmed.

NOTE:

If you have an answering machine (or answering service) attached to the same

phone line as the unit, set the unit count for two (

) or more rings higher than the

answering machine/service count. See also

Override Telephone Company Answering

Service

(See Below).

Unit will Answer a Remote Call after 7 Rings

Example:

Override is enabled. The unit will answer the second call after

a few number of rings, hang up and callback is performed.

Enable or Disable Telco Mode:

Press

Then

Enable (

) or Disable (

). Then (#)

Telco mode is using the

main

telephone line for the unit’s communications to a house or

complex.

Enable

the Telco mode if the unit

will

use a regular telephone line.

Disable

the Telco mode if the unit

will not

have a regular telephone line connected to it. If the

Telco mode is disabled and the unit is connected to a regular telephone line, it will ignore

all

Telco features (call forwarding, call waiting, etc.).

Factory Setting: Enabled

Telco mode is disabled.

Example:

Dial "0-9" First to Get an Outside Line Using an Automated Phone System:

Press

Then

Enable (

) or Disable (

). Then (#)

When the unit is connected to a PBX telephone system (Automated), it can be programmed

to dial a specific PBX number (0-9) then pause briefly, allowing the PBX system to give the

unit an outside line.

Factory Setting: Disabled

Example:

Enables Unit to dial "9 and Pause" to connect to an outside line.

Enter Specific PBX Digit (0-9). Then (#)

109

113