Linksys EFG250 /en/US/docs/storage/nass/csbcdp/efg250/user/guide/EFG250_V2_use - Page 46

Appendix B: Installing a Second Hard Drive, Cable Select, B-1: Attach IDE Cable

Get Linksys EFG250 - EtherFast NAS Server PDF manuals and user guides
UPC - 745883559220
View all Linksys EFG250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

EtherFast Network Attached Storage (250GB with PrintServer) Appendix B: Installing a Second Hard Drive NOTE: The Network Attached Storage support IDE Ultra DMA (or UDMA) hard drives with a throughput of 33-66Mbps (ATA/33, ATA/66) and a rotation speed of 5400 or 7200 rpms. When you are ready to install a second hard drive into the Network Attached Storage, follow these instructions: 1. Power down the Network Attached Storage by pressing the power button on the front panel. Then unplug the power adapter from the Network Attached Storage. 2. Unlock the second drive bay. This bay is empty and will hold your new drive. 3. Make sure that your hard drive's master/slave jumpers are set to Cable Select before putting it in the drive tray. For instructions on these jumper settings, refer to the documentation included with your hard drive. 4. Attach the IDE cable from the drive tray to your hard drive. (The IDE cable is the wider of the two cables in the drive tray.) Make sure you plug this securely into your hard drive. 5. Attach the power cable from the drive tray to your hard drive. (The power cable is the smaller of the two cables in the drive tray.) Make sure you plug this securely into your hard drive. Figure B-1: Attach IDE Cable Appendix B: Installing a Second Hard Drive Figure B-2: Attach Power Cable 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
39
Appendix B: Installing a Second Hard Drive
EtherFast Network Attached Storage (250GB with PrintServer)
Appendix B: Installing a Second Hard Drive
When you are ready to install a second hard drive into the Network Attached Storage, follow these instructions:
1.
Power down the Network Attached Storage by pressing the power button on the front panel. Then unplug the
power adapter from the Network Attached Storage.
2.
Unlock the second drive bay. This bay is empty and will hold your new drive.
3.
Make sure that your hard drive’s master/slave jumpers are set to
Cable Select
before putting it in the drive
tray. For instructions on these jumper settings, refer to the documentation included with your hard drive.
4.
Attach the IDE cable from the drive tray to your hard drive. (The IDE cable is the wider of the two cables in the
drive tray.) Make sure you plug this securely into your hard drive.
5.
Attach the power cable from the drive tray to your hard drive. (The power cable is the smaller of the two
cables in the drive tray.) Make sure you plug this securely into your hard drive.
NOTE:
The Network Attached Storage support IDE Ultra DMA (or UDMA) hard drives with a
throughput of 33-66Mbps (ATA/33, ATA/66) and a rotation speed of 5400 or 7200 rpms.
Figure B-1: Attach IDE Cable
Figure B-2: Attach Power Cable