MSI MS 7030 User Guide - Page 54

Day of Month Alarm

Get MSI MS 7030 - K8N Neo Platinum Motherboard PDF manuals and user guides View all MSI MS 7030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

MS-7030 ATX Mainboard [DPMS Support] Initial display power management signalling. HDD Power Down If HDD activity is not detected for the length of time specified in this field, the hard disk drive will be powered down while all other devices remain active. Settings are [Disabled] and [1] through [15] Min. HDD Down In Suspend This item determines whether the hard disk drive will be turned off during suspend mode. Settings: [Disabled] and [Enabled]. Power Button Function This feature sets the function of the power button. Settings are: [Power Off] The power button functions as normal power off button. [Suspend] When you press the power button, the computer enters the suspend/sleep mode, but if the button is pressed for more than four seconds, the computer is turned off. PWRON After PWR-fail This item specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are: [Off] Leaves the computer in the power off state. [On] Leaves the computer in the power on state. [Former-Sts] Restores the system to the status before power failure or interrupt occurred. Wake-Up Event Activity Press and the following sub-menu appears. WOL (PME#) From Soft-Off When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PME (Power Management Event). Settings: [Enabled], [Disabled]. Power-On by Alarm The field is used to enable or disable the feature of booting up the system on a scheduled time/date. Settings: [Enabled], [Disabled]. Day of Month Alarm The field specifies the date for Power-On by Alarm. Settings: [0]~[31]. Time(hh:mm:ss) Alarm The field specifies the time for Power-On by Alarm. Format is . 3-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
3-18
MS-7030 ATX Mainboard
[DPMS Support]
Initial display power management signalling.
HDD Power Down
If HDD activity is not detected for the length of time specified in this field, the hard disk
drive will be powered down while all other devices remain active. Settings are
[Disabled] and [1] through [15] Min.
HDD Down In Suspend
This item determines whether the hard disk drive will be turned off during suspend
mode. Settings: [Disabled] and [Enabled].
Power Button Function
This feature sets the function of the power button. Settings are:
[Power Off]
The power button functions as normal power off button.
[Suspend]
When you press the power button, the computer enters the
suspend/sleep mode, but if the button is pressed for more
than four seconds, the computer is turned off.
PWRON After PWR-fail
This item specifies whether your system will reboot after a power failure or interrupt
occurs. Available settings are:
[Off]
Leaves the computer in the power off state.
[On]
Leaves the computer in the power on state.
[Former-Sts]
Restores the system to the status before power failure or
interrupt occurred.
Wake-Up Event Activity
Press <Enter> and the following sub-menu appears.
WOL (PME#) From Soft-Off
When set to [Enabled], the feature allows your system to be awakened from the
power saving modes through any event on PME (Power Management Event).
Settings:
[Enabled], [Disabled].
Power-On by Alarm
The field is used to enable or disable the feature of booting up the system on a
scheduled time/date. Settings: [Enabled], [Disabled].
Day of Month Alarm
The field specifies the date for
Power-On by Alarm
.
Settings: [0]~[31].
Time(hh:mm:ss) Alarm
The field specifies the time for
Power-On by Alarm
. Format is <hour><minute>
<second>.