Marantz SR4600 SR4600 User Manual - Page 11
Programming The Remote Controller, Pure Direct Button, Setup / T.tone Button, Osd Button, Sleep - 7 1 amp
View all Marantz SR4600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
ENGLISH ¤1 PURE DIRECT button When this button is pressed, the tone control circuit is bypassed. ¤2 SETUP / T.TONE button (when AMP mode is selected) Used to enter the test tone menu. ¤3 OSD button Note: • This button is unavailable for SR4600. ¤4 SLEEP (sleep timer) button This button is used for setting the sleep timer. It can be operated the same way as the button on the unit. ¤5 TV VOLUME UP ( ) /DOWN ( ) buttons These buttons increase or decrease TV's volume. 8 PROGRAMMING THE REMOTE CONTROLLER The remote controller RC5500SR must be programmed to use the codes for your appliances of different brands. This is done by keying in a 4digit code or by scanning the codes until the correct one is found. We recommend to using the 4-digit code. This mode is faster and more reliable. The code scanning method should be used only if you cannot find the code for one of your appliances. The codes are listed at the end of this book. Important: • Use the remote control buttons for programming, not the buttons of the receiver or other appliances. • Some codes may be not match your equipment. In this case, your equipment cannot be controlled with this remote controller. PROGRAMMING WITH THE 4-DIGIT CODE ENTER 1. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. 1. 2. SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH OSD MENU T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY 1. Press and hold down the Function Selector button for the appliance which should be controlled and press SETUP button until the indicator blinks twice. 2. Press the 4-digit code for appliance (code table at the end of this book) 3. When the procedure is successful, the indicator will blink twice. Note: • If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again. SCANNING THE CODE TABLE 4. 2. 4. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. OSD MENU 2. 6. 3. ENTER SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 23 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH 1. Switch on the appliance which should be controlled. 2. Press and hold down the Function Selector button for appliance which should be controlled and press SETUP button until the indicator blinking twice. 3. Press the code 9 - 9 - 1. The indicator will blink twice. 4. Aim the remote control at the appliance and slowly alternate between pressing POWER button and the Function Selector button for the appliance. 5. Stop when the appliance turns off. 6. Press SETUP button once to lock in the code. CHECKING THE CODE 1. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. OSD MENU 1. 3. 4. 2. ENTER SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT 1. Press and hold down the Function Selector button for appliance which should be controlled and press SETUP button until the indicator blinking twice. 2. Press the code 9 - 9 - 0. The indicator will blink twice. 3. To view the code for first digit, press 1 once. Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number. Note: If a code digit is "0", the indicator will not blink. 4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. RESETTING THE ALL CODE OSD MENU POWER ENTER 1. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. 1. 2. SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 23 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP OSD MENU BASS TREBLE TUNE/SEARCH 1. Press and hold down the any Function Selector button and press SETUP button until the indicator blinking twice. 2. Press the code 9 - 8 - 1. The indicator will blink twice. Then, RC5500SR will return to the factory preset code. Note: • After this procedure, the selected function button is set initial code and other function buttons are set initial code too. Once you have found and the codes for your various appliances, you may want to write them down here. TV VCR DSS DVD CD TAPE CDR MD