Marantz SR4600 SR4600 User Manual - Page 15
Connecting Audio Components - power cord
View all Marantz SR4600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
ENGLISH Caution: • Be sure to use speakers with the specified impedance as shown on the rear panel of this unit. • To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. • Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks. • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit. Note: • Be sure to connect the positive and negative cables for the speaker properly. If they are missconnected, the signal phase will be reversed and the signal quality will be corrupted. CONNECTING A SUBWOOFER Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in ). If your subwoofer is a passive type (power amplifier is not built in), connect a monaural power amplifier to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifier. CONNECTING AUDIO COMPONENTS CD RECORDER / MD DECK OUT DIGITAL OUTPUT L R OUT IN DIGITAL DIGITAL INPUT OUTPUT L L LR R R CD PLAYER OUT IN L L R R LR LR TAPE DECK LR RL RL LR LR ANALOG AUDIO LR FM (75Ω) GND AM ANTENNA L R CD IN OUT TAPE VIDEO IN OUT DSS / VCR2 IN OUT VCR1 DVD IN OUT CDR/MD IN OUT DSS / VCR2 IN OUT VCR1 AUDIO DVD MONITOR IN VCR1OUT TV L SL C SVIDEO DVD MONITOR IN SBL RC-5 OUT R SR SW SBR 1 TV 7.1CH INPUT 2 OPT. 3 4 OUT DIGITAL DIGITAL AUDIO (COAXIAL) COMPONENT VIDEO Y COAX. OUT CB/PB DIGITAL AUDIO CR/PR (OPTICAL) DVD DSS / VCR 2 MONITOR AC IN AUDIO PRE OUT L SL C SBL R L R L R L UNSWITCHED 1A 120W MAX R SR SW SBR FRONT SURROUND BACK S. SPEAKER B SPEAKER SYSTEMS MINIMUM 6 OHMS SURROUND CENTER SWITCHED 1A 120W MAX AC OUTLETS 120V 60HZ RL RL The output audio signal from the TAPE OUT jack and the CD-R/MD OUT jack is the same signal which is currently selected. Caution: • Do not connect this unit and other components to mains power until all connections between components have been completed. Notes: • Insert all plugs and connectors securely. Incomplete connections may make noise. • Be sure to connect the left and right channels properly. Red connectors are for the R (right) channel, and white connectors are for the L (left) channel. • Be sure to connect input and output properly. • Refer to the instructions for each component that is connected to this unit. • Do not bind audio/video connection cables with power cords and speaker cables this will result in generating a hum or other noise. CONNECTING DIGITAL AUDIO COMPONENTS • There are 4 digital inputs, 2 coaxial jacks and 2 optical jacks, on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components. • There is one digital output coaxial jack and one optical output jack on the rear panel. These jacks can be connected to a CD recorder-, or a MD deck inputs, respectively. • Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source's connected to digital input jacks. • Use fiber optical cables (optical) for DIG-1,2 input jacks. Use 75 ohms coaxial cables (for digital audio or video) for DIG-3, 4 input jacks. • You can designate the input for each digital input/ output jacks according to your component. See page 17. Notes: • There is no Dolby Digital RF input jack. Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack. • The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly. • Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively. 12