Marantz SR4600 SR4600 User Manual - Page 30

ENGLISH OTHER FUNCTION ATTENUATION TO ANALOG INPUT SIGNAL K ATT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR DISPLAY MEMORY CLEAR EXIT BAND T-MODE VOLUME DOWN MUTE UP ATT BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY CH.SEL LIP.SYNC SYSTEM REMOTE CONTROLLER RC5500SR If the selected analog audio input signal is greater than the capable level of internal processing, the "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote. "ATT" indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/VCR2-OUT. This function is memorized for each individual input source. LISTENING THROUGH HEADPHONES This jack may be used to listen to the SR4600's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.) AV SURROUND RECEIVER SR4600 INPUT SELECTOR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIG DISC 6.1 MT X 6.1 7.1CH INPUT STANDBY POWER ON/STANDBY S. SPEAKER B PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER Notes: • When using headphones, the surround mode will change to STEREO and TruSurround (TS) headphones by SURROUND MODE button. • The surround mode returns to the previous setting as soon as the plug is removed from the jack. VIDEO ON/OFF When no video signal is connected to the SR4600 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. To select video off, press the V-OFF button on the remote. T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY CH.SEL LIP.SYNC DISPLAY MODE AV SURROUND RECEIVER SR4600 R DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR S. SPEAKER B PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY EXIT BAND SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 23 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT You can select the display mode for the front display of the SR4600. To select this mode, press the DISPLAY on the front panel or on the remote. When this button is pressed, the display mode is switched in the following sequence. → Surround Mode → Auto-display Off → Display Off → Input Function → Surround Mode.... In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. In Display off mode, the display is off completely. Note: • Only the DISP indicator will be illuminated on the front display, in display off condition SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source with the A/D button on the remote controller. When this button is pressed, the input mode is switched in the following sequence. → Digital Auto → Digital → Analog → Digital Auto.... In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. In Digital mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory. If you need to change the input mode completely, use INPUT setup in SETUP MENU system. (see page 17) 27