Marantz SR4600 SR4600 User Manual - Page 9

ENGLISH REAR PANEL zx cv bn m FM (75Ω) GND AM ANTENNA L VIDEO IN OUT DSS / VCR2 IN OUT VCR1 DVD MONITOR IN VCR1OUT TV L SL C SVIDEO DVD MONITOR IN SBL RC-5 OUT COMPONENT VIDEO Y CB/PB R CD IN OUT IN OUT IN OUT IN OUT TAPE CDR/MD DSS / VCR2 VCR1 DVD TV AUDIO R SR SW SBR 1 7.1CH INPUT 2 OPT. 3 OUT DIGITAL CR/PR 4 COAX. OUT DVD DSS / VCR 2 MONITOR AC IN AUDIO PRE OUT L SL C SBL R L R L R L UNSWITCHED 1A 120W MAX R SR SW SBR FRONT SURROUND BACK S. SPEAKER B SPEAKER SYSTEMS MINIMUM 6 OHMS SURROUND CENTER SWITCHED 1A 120W MAX AC OUTLETS 120V 60HZ ⁄3 ⁄2 ⁄1 ⁄0 ., z AUDIO IN/OUT (CD, TAPE, CD-R/MD, TV, DVD, VCR1, DSS/VCR2) These are the analog audio inputs and outputs. There are 7 audio inputs (4 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. x FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. c VIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2) These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs. The 2 video output channels can be used to be connected to video tape recorders for making recordings. The input signals of video and S-video are converted each other, and each of the converted video signals can be output. v MONITOR OUT This is a monitor output and each one includes both composite video and S-video configurations. b REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. n DIGITAL INPUT (Dig.1 - 4) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components. m COMPONENT VIDEO INPUT/OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR4600. The SR4600 has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. , AC INLET Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. SR4600 can be powered by 120V AC only. . AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the SR4600 is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the SR4600 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch. Caution: • In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR4600 is turned on. • The capacity of this AC outlet is 100W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply. ⁄0 7.1 CHANNEL INPUT By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. ⁄1 Speaker outputs terminals Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers. Note: • You can use surround back speaker terminals as S(Surround) SPEAKER B terminals, when you use no surround back speaker. ⁄2 Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifiers. ⁄3 Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. 6