Marantz SR4600 SR4600 User Manual - Page 23

ENGLISH 2-3. SPEAKERS LEVEL SETTING WITH TEST TONE Here you will set the volume for each speaker so that they are all heard by the listener at the same level. Moreover, if the T.TONE button is pressed, unit can enter into this menu directly. 1. When you select "MANUAL" in T-MODE menu by pressing the or button, this unit will emit a pink noise from the front left speaker. At this time, adjust the desired level of the master volume. Remember the level of this noise and MMEENNUUSSTTRRUCUTCUTRUERoEf SopfeSakpeeraLkeevresl sLeetvuepl setup Direct select Speakers by remote Distance control setup Test Tone mode Note: • The speaker level settings are not available in 7.1 Channel Input mode, CS mode and Multi Channel Stereo mode. T(TEST) MODE : Selects "MANUAL" or "AUTO" for generating mode of test tone or cursor button. If you select "AUTO" by pressing the button, the test tone will be cycled through in a circular pattern then press the button. This unit will emit the pink noise from the center speaker. 2. Using the and cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker (Note that this can be adjusted to any level between - 10 and +10 dB in 1dB intervals). Maximum +10dB MANU Speaker Speakers L Level setup SL AUTO (Auto) SW C Listening Positiom R SR which is L (Left) → C (Center) → R (Right) → SR (Surround Right) → SBR (Surround Back Right) → SBL (Surround Back Left) → SL (Surround Left) → +9dB SBL SBR SW (Subwoofer) → L →.. increments of 2 seconds for each channel. Using the and cursor buttons, adjust the 1 dB interval button TO MAIN MENU RETURN EXIT volume level of the noise from the speaker so that Reference 0dB it is the same level for all speaker. Press the ENTER button, you can stop the test tone mode. Or press the or cursor button to 1 dB interval button MAIN MENU Speakers Distance setup exit SETUP MENU select "EXIT" then press the ENTER button to exit the SETUP MENU. -9dB Or press the or cursor button to select "RETURN" then press the ENTER button to return Minimum -10dB the previous "2-2. Speakers Distance" setup. (SW -15 dB) If you select "MANUAL", adjust the output level of each speaker as follow. 1. 3. 5. 1. 5. 1. 2. 5. 5. AV SURROUND RECEIVER SR4600 INPUT SELECTOR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR 7.1CH INPUT STANDBY POWER ON/STANDBY S. SPEAKER B PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE 2. 5. 1. 5. 1. 3. 5. 20 AUX1 TV VOL. SLEEP AMP MUTE MAINN VOL. OSD MENU ENTER SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 MENU OFF 2 EX/ES 5 DTS 3 VIRTUAL 6 5. 3. Press the cursor button again. This unit will now emit the pink noise from the front right speaker. 4. Repeat steps 2 and 3 above for the front right and other speakers until all speakers are adjusted to the same volume level. 5. Press the ENTER button, you can stop the test tone mode. Or press the or cursor button to select "EXIT" then press the ENTER button to exit the SETUP MENU. Or press the or button to select "RETURN" then press the ENTER button to return the previous "2-2. Speakers Distance" setup. Notes: • Speakers that you selected "None" for in the Speaker Size Setup menu will not appear. • The setup level for each channel is memorized for reproduction in all surround mode by this method exclude CS mode, Multi channel stereo mode and 7.1 ch input mode. • To adjust the speaker levels for 7.1-channel input sources, you will need to use the 7.1CH Level Input setup menu. 2-4. SPEAKERS LEVEL SETTING WITHOUT TEST TONE Channel level (speaker level) can be adjusted without using test tone. Note: • Four channel level settings can be memorized for reproduction: the 7.1 ch input mode, CS mode, Multi channel stereo mode, and all other surround modes, respectively. 1. Set the surround mode or 7.1 ch input mode which you want to adjust the channel level. 2. Press the CH.SEL button on the remote. 3. Select the desired channel (speaker) with the or cursor buttons. 4. Adjust the level with the or cursor buttons. 5. After completing the setup, press the CH.SEL button again.