Marantz SR4600 SR4600 User Manual - Page 17
Advanced Connecting, Connecting The Remote Control Jacks - subwoofer
View all Marantz SR4600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS RL RL LR CENTER L R FRONT SURR. SUB SURR. WOOFER BACK POWER AMPLIFER Subwoofer Front Center Front Left Right Surround Surround Left Right RL RL LR FM (75Ω) GND AM ANTENNA L VIDEO IN OUT DSS / VCR2 IN OUT VCR1 DVD MONITOR IN VCR1OUT TV L SL C S V DVD SBL MONITOR R CD IN OUT IN OUT IN OUT IN OUT TAPE CDR/MD DSS / VCR2 VCR1 DVD TV AUDIO R SR SW SBR 1 7.1CH INPUT AUDIO PRE OUT L SL C SBL R L R L R L R SR SW SBR FRONT SURROUND BACK S. SPEAKER B SPEAKER SYSTEMS MINIMUM 6 OHMS SURROUND CENTER LR RL RL 2 MONITOR IN VCR1OUT TV L SL C SVIDEO DVD MONITOR IN SBL RC-5 OUT COMPONENT VIDEO Y CB/PB R SR SW SBR 1 TV 7.1CH INPUT 2 OPT. 3 OUT DIGITAL CR/PR 4 COAX. OUT DVD DSS / VCR 2 MONITOR AC IN R L R L UNSWITCHED 1A 120W MAX RROUND BACK . SPEAKER B NIMUM 6 OHMS SURROUND CENTER SWITCHED 1A 120W MAX AC OUTLETS 120V 60HZ REMOTE CONTROL IN OUT 1 CD RECORDER EXTERNAL INTERNAL REMOTE CONTROL IN OUT MD DECK EXTERNAL INTERNAL RC OUT OPTION REMOTE CONTROL IN OUT CD PLAYER EXTERNAL INTERNAL Surround Back Left Surround Back Right LR LR LR CENTER L R FRONT SURR. SUB WOOFER SURR. BACK DVD AUDIO PLAYER or SACD MULTI CHANNEL PLAYER CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the 7.1 channel input level menu. See page 29. CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. 14 q You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you only need to aim the remote at one unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR4600, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure. 1. Hold down the 7.1CH INPUT button and MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the or cursor button to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled. Note: Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE".