Marantz SR7002 User Manual - English - Page 20

BASIC OPERATION USE MODE (Normal operation status) This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD/CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier). Learning is not necessary for Marantz products. You can use these products without setting any codes. 1. Press the SOURCE button. For this example, press DVD. DVD is shown on the LCD, and the remote controller is set for DVD. Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed. To change the amplifier or other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifier source changes to DVD. 2. Press the buttons to operate the DVD. The indicator is shown on the LCD while the remote control codes are being transmitted. It is not displayed when buttons without stored code are pressed. 3. The direct buttons can be used to perform up to 20 operations for each of the 12 sources, including DVD, TV, AMP, and other AV equipment. The buttons consist of the D1 to D5 buttons, and the equipment is operated by pressing the buttons corresponding to the indicators on the LCD. Four pages are available, and press the > button to select a page. The current page position is displayed on the LCD. PRESET MODE (When operating non-Marantz AV equipment products) This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, VCR, LD, CABLE, DSS, DVD, TAPE, TUNER, CD/CD-R, MD and AMP. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the SOURCE button of the remote controller. See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings. Remote control Corresponding source name preset code Device name TV TV Television DVD DVD DVD player VCR VCR Video deck DSS SATELLITE Satellite broadcasting tuner equipment TUNER RECEIVER/TUNER AM FM TUNER CD CD/CD-R PLAYER CD player CD-R CD/CD-R PLAYER CD recorder MD CD/CD-R PLAYER MD deck TAPE TAPE Cassette deck AUX1 CABLE Cable television AUX2 LASER DISC Laser disc player AMP AMPLIFIER Amplifier or receiver RECEIVER/TUNER • When using Marantz products, TV and DVD can be set to TV1 (TV/VDP: Projector) and TV2 (PDP: Plasma display), and DVD1 (first DVD player) and DVD2 (second DVD player), respectively, to match the customer's operating environment. These settings are made in PRESET mode. In the factory default state, the remote controller is set to TV1 and DVD1. To make the presets, enter the numbers below while referring to the section "Entering and Setting the Manufacturer Number Directly". TV1: 0001, TV2: 0002 DVD1: 0001, DVD2: 0002 Entering and Setting the Manufacturer Number Directly Refer to the manufacturer number list. This example shows how to set a SAMSUNG DVD player. 2 3 4 LEARN NAME MACRO USE PAGE 1 2 3 4 5 LEARN NAME MACRO USE PAGE 1 2 3 4 6 LEARN NAME MACRO USE PAGE 1 2 3 4 LEARN NAME MACRO USE PAGE 1 2 3 4 LEARN NAME MACRO USE PAGE 1 2 3 4 1. View the supplied manufacturer number list, and find the number of the manufacturer for the device that you are using. 2. Hold down the M button for three seconds or more. The menu is displayed. 3. Press the D1 (PRESET) direct button. The Preset setting (P-SET) is displayed. 4. Press the DVD source button. 5. Press the numeric buttons to enter the four- digit manufacturer number. Example: To enter "0600" from the manufacturer number list. To correct the entered number, use the 1 or 2 cursor button to enter the correct number. • If no button is pressed for over one minute during the setting process, any settings that were made are cancelled. 6. Press the OK cursor button. 7. Confirm the OK is displayed and then the display returns to the Preset Setting (P-SET). When the manufacturer number is entered correctly, OK is displayed momentarily on the screen. • If you enter a number not in the manufacturer number list, WRONG CODE is displayed, and then you return to the preset setting again Check the manufacturer number list, and either set a different number or use the sequence function to set. 8. To set the manufacturer number for another source device, repeat the procedure in steps 4 to 6. 9. After the settings are completed, press the M button. 10. Press the buttons on the remote controller to check that the DVD can be operated correctly. Setting Equipment Not Appearing in Manufacturer Number List Use the sequence function to set equipment not appearing in the manufacturer number list. You may still be unable to set some equipment even when using the sequence function. In this case, the remote controller can be programmed with codes individually. In the sequence function, the power ON/OFF codes are transmitted by pressing the remote controller buttons in order. If the power for the equipment is left on, hold down the button until the equipment is turned off, and then release. This completes the setting. This example shows how to set a DVD player. 4 5 7 LEARN NAME MACRO USE PAGE 1 2 3 4 LEARN NAME MACRO USE PAGE 1 2 3 4 LEARN NAME MACRO USE PAGE 1 2 3 4 1. Turn on the power of the DVD player. 2. Hold down the M button for three seconds or more. The menu is displayed. 3. Press the D1 (PRESET) direct button. The Preset setting (P-SET) is displayed. 4. Press the DVD source button. 5. Hold down the CH+ or CH- button for one second or more. 6. Press the CH+ button repeatedly in the interval for one second. The signal is transmitted, and the display cycles through the code number. Press the CH- button to go back to a number screen. 7. Release the button once the DVD player turns off. 8. Press the OK cursor button. 9. Confirm the OK is displayed and then the display returns to the Preset Setting (P-SET). 10. To set the manufacturer number for another source device, repeat the procedure in steps 4 to 8. 11. After the settings are completed, press the M button. 12. Press the buttons on the remote controller to check that the DVD can be operated correctly. Check the following points if the equipment which was set does not operate properly. • If there is more than one number in the manufacturer number list, try setting a different number. • There may be some buttons which cannot be used. Program the codes to the required buttons. 17 ENGLISH