Marantz SR7002 User Manual - English - Page 62

ADJUSTING THE TONE (BASS & TREBLE) CONTROL LEARN NAME MACRO USE PAGE 1 2 3 4 M D1 D2 D3 D4 D5 CH VOL TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics. (Using the remote controller) To adjust the tone, press the AMP button and press the > button PAGE3 is displayed. To adjust the bass effect, press BASS+ (D2) or BASS- (D3). To adjust the treble effect, TREB+ (D4) or TREB- (D5). Notes: • The tone control function is unavailable for the Source Direct, Pure Direct, Headphone, Dolby Virtual Speaker, THX mode, and 176.4/192kHz PCM. • The tone control function is not available when ACOUSTIC EQ is being used. • Additionally, tone control is not available during Dolby TrueHD, Dolby Digital Plus, or DTS-HD playback. TEMPORARILY TURNING OFF THE SOUND OK PREV MENU LIP.SYNC GUIDE MUTE EXIT TEST 1 CH.SEL 2 SURR 3 7.1CH 4 ATT 5 SPK-AB 6 DISP OSD SLEEP 7 8 9 To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the remote controller. This will interrupt the output to all speakers and the head-phone jack, but it will not affect any recording or dubbing that may be in progress. When the system is muted, the display will show "MUTE" . Press the MUTE button again to return to normal operation. USING THE SLEEP TIMER PREV MENU TEST 1 7.1CH 4 DISP 7 CLEAR LIP.SYNC GUIDE CH.SEL 2 ATT 5 OSD 8 THX 0 MUTE EXIT SURR 3 SPK-AB 6 SLEEP 9 MEMO To program this unit for automatic standby, press the SLEEP button on the remote controller. Each press of the button will increase the time before shut down in the following sequence. OFF 10 20 30 40 50 120 110 100 90 80 70 60 The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows "SLEEP OFF" and the SLEEP indicator will disappear. M-DAX (Marantz Dynamic Audio eXpander) USE PAGE 4 M D1 D2 D3 D4 D5 CH VOL TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 This function makes up for lost audio content in MP3 or AAC sources (from lossy compression) during playback. Choose one of the following levels for this effect as desired. "HIGH": Stronger effect "LOW": Weaker effect "OFF": Deactivated. (Using the remote controller) When switching to M-DAX mode, press the AMP button and then the > button until the PAGE 4 is displayed. When "M-DAX" is displayed on the remote controller, press the M-DAX (D5) button. Each time this button is pressed, M-DAX changes as follows. OFF LOW HIGH Notes: • M-DAX is compatible with PCM (48 kHz or lower) and two-channel analog sources. • The M-DAX is not available when Dolby Virtual Speaker mode is being used. VIDEO CONVERT ANALOG VIDEO CONVERSION This unit is equipped to convert video signals for monitor output. Because of this, indifferent of the connection (VIDEO, S-VIDEO, COMPONENT VIDEO) between the playback device and this unit, listening and viewing are possible with a single higher grade cable between the MONITOR OUT terminal of the unit and the monitor. UP-CONVERSION FROM ANALOG VIDEO SIGNALS TO HDMI The up-conversion feature of this unit can output the input analog video signals (for component video signals of 480i, 480p, 1080i and 720p resolution, and S-Video and Video (composite) of 480i resolution) to the HDMI MONITOR terminal. Notes: • HDMI video input is only output to the HDMI MONITOR OUT terminal of the unit. If connecting a playback device such as a DVD player to the HDMI input jack, connect the HDMI MONITOR OUT terminal of the unit to a TV monitor. • This mode is unavailable for the REC out terminal. • This mode is unavailable for still picture, fast forward and reverse play on video component. • If, while attempting to use the video convert feature, the unit cannot synchronize with the display device, "NO SIGNAL" appears on the monitor or noise is generated, this feature cannot be used. All of these signs are caused by equipment incompatibility; there is nothing wrong with the unit. If this occurs, set "VIDEO CONVERT" in the "VIDEO SETUP" menu to "DISABLE". Next, connect the video input signal to the display component via the MONITOR OUT terminal under VIDEO and the S-video input signal to the display component via the MONITOR OUT terminal under S-VIDEO. • The video convert feature constantly monitors input video signals and determines whether to convert the input signals or not. However, some input video signals cannot be detected correctly. If this occurs, set "VIDEO CONVERT" in the "VIDEO SETUP" menu to "DISABLE". • For optimal video performance, THX recommends setting the "VIDEO CONVERT" mode "DISABLE". CONNECTION EXAMPLE • When a monitor is connected to the HDMI MONITOR OUT terminal of the unit AV SURROUND RECEIVER SR8002 INPUT SELECTOR PURE DIRECT DSD STANDBY POWER ON/OFF PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER BAND T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT M-DAX SPEAKERS A/B MIC VOLUME DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R VIDEO or S-VIDEO or component or HDMI HDMI Notes: • If the resolution of the component video signal input from the playback device is other than 480i, 480p, 1080i or 720p, images are not output from the HDMI MONITOR OUT terminal of the unit. • If the resolution of the S-Video or Video signal input from the playback device is other than 480i, images are not output from the HDMI MONITOR OUT terminal of the unit. • When a monitor is connected to the VIDEO or SVIDEO MONITOR OUT terminals of the unit AV SURROUND RECEIVER SR8002 INPUT SELECTOR PURE DIRECT DSD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MTX 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR STANDBY POWER ON/OFF PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER BAND T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT M-DAX SPEAKERS A/B MIC VOLUME DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R VIDEO or S-VIDEO or component HDMI VIDEO or S-VIDEO 59 ENGLISH