Marantz SR7002 User Manual - English - Page 56

4 VIDEO SETUP Video settings are made as follows. 1. Select "4. VIDEO SETUP" from the MAIN MENU with the 3/4 cursor buttons and press the OK/ENTER button. 4.VIDEO SETUP VIDEO CONVERT TV.AUTO OSD INFO I/P CONVERT HDMI OUT COMPO OUT2 :DISABLE :ENABLE :ENABLE :OUTPUT1 :MAIN RETURN NEXT EXIT 2. Select the desired menu with the 3/4 cursor buttons and press the OK/ENTER button. • VIDEO CONVERT "4-1 VIDEO CONVERT" • TV-AUTO Select the TV AUTO ON/OFF function to enable or disable with the 1 or 2 cursor buttons. (refer to page 66) • OSD INFO Select the OSD information function to "ENABLE" or "DISABLE" with the 1 or 2 cursor buttons. If you select "ENABLE", this unit will display the status of the feature (Volume up/down, input select, etc..) on the monitor. If you do not desire this information, select "DISABLE". Note: • OSD information is not output to Monitor Output of HDMI and Component Video. However, OSD information is output if the Video Convert function is used to output Video or S-Video video signals to Monitor Out of HDMI and Component Video. For details, refer to"VIDEO CONVERT"on page 59. • IP CONVERT Select the IP CONVERT ON/OFF function to enable or disable with the 1 or 2 cursor buttons. (refer to page 59) • HDMI OUT This setting is for selecting which output terminal, HDMI 1 or HDMI 2, to output the signal to. Select the output destination with the 1 / 2 cursor buttons. To use the remote controller (RC8001SR) to change the HDMI OUT setting, press the AMP button and then the > button until the second page is displayed. After HDMI 1 or HDMI 2 is displayed on the remote controller, press the D3 or D4 button to switch between them. USE PAGE 2 M D1 D2 D3 D4 D5 CH VOL TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 • COMPONENT OUT 2 (This feature is not available on the SR7002.) This setting is for selecting whether to output the images for the main room or the images for the multi room system to the COMPONENT MONITOR OUT 2 terminal. Select the output destination between MAIN and MULTI with the 1 / 2 cursor buttons. Note: • When MULTI is selected, video signals converted from the MONITOR OUT 2 terminal are not output. After you complete this portion of the setup, move cursor to "RETURN" with the 3, 4, 1 and 2 cursor buttons and press the OK/ENTER button. 4-1 VIDEO CONVERT This unit is equipped to convert video signals for monitor output. This section explains how to set up conversion for each type of video input. 1. Select "4. VIDEO SETUP" from the MAIN MENU with the 3 / 4 cursor buttons and press the OK/ENTER button. 2. Select "VIDEO CONVERT" with the 3 / 4 cursor buttons and press the OK/ENTER button. VIDEO CONVERT TV : ANA&HDMI DVD : ANA&HDMI VCR1 : ANA&HDMI DSS : ANA&HDMI AUX1 : ANA&HDMI TAPE : ANA&HDMI CD/R : ANA&HDMI AUX2 : ANA&HDMI RETURN BACK EXIT 3. Select "FUNCTION" with the 3 / 4 cursor buttons and set the video conversion mode with the 1 / 2 cursor buttons ANA&HDMI: This mode both up-converts and down-converts analog video signals (Composite Video, S-Video, Component Video). Furthermore, it up-converts from analog video signal to HDMI. (It cannot downconvert from HDMI digital video signals to analog video signals.) ANA ONLY: This mode both up-converts and down-converts analog video signals (Composite Video, S-Video, Component Video). It does not up-convert to HDMI. OFF: This mode turns off all conversion features. Note: • For details on video convert feature, see page 59. 53 ENGLISH