Marantz SR7002 User Manual - English - Page 46

ENGLISH

43

1-1

FUNC INPUT SETUP

(ASSIGNABLE DIGITAL INPUT)

The 6 and F (Front) digital inputs can be assigned to

a desired source.

HDMI and COMPONENT inputs can be assigned to

the preferred source.

Use this menu to select which digital input jacks are

to be assigned to which input source.

1.

Select “

FUNC INPUT SETUP

” from the

1.INPUT SETUP menu with the

3

or

4

cursor

buttons and press the

OK

/

ENTER

button.

FUNC INPUT SETUP 1

FUNC:MODE DIG HDMI COMP V/S

TV :

AUTO

1

1

1

1

DVD :AUTO

2

2

2

2

VCR1:AUTO

3

3

3

3

DSS :AUTO

4

4

4

4

AUX1:AUTO

F

-

-

RETURN

NEXT

T

EXIT

2.

Select a setting with the

3

,

4

,

1

, and

2

cursor

buttons, and assign a mode and input jack

(DIG, HDMI, COMP, V/S).

MODE

AUTO:

Select “

AUTO

”, for automatic detection of the

digital input signal condition.

If there is no digital signal, but there is an analog

signal present,

the analog signal will be played.

"AUTO" is the initial setting of all input sources.

HDMI:

Select “

HDMI

”

, when only a HDMI signal will be

used

.

DIG:

Select “

DIG

”, when only a digital signal will be

used.

ANA:

Select “

ANA

” for input sources for which no digital

input jacks are used.

DIG

6 and F(Front) digital inputs can be assigned to a

desired source.

Assign the number of a digital input jack to the

device.

HDMI

Assign the number of an HDMI input jack to the

device.

Note:

• When FUNCTION MODE is set to HDMI and

HDMI AUDIO of “5. PREFERENCE” is set to

THROUGH, audio is not output from the unit. (See

page 54)

COMP

Assign the number of a component video input

jack to the device.

V/S

Assign the number of a composite video and S-

video input jack to the device.

Note:

• Video and S-video can use the same numbers when

assigning to input functions.

• The

✽

mark in AUX.1 indicates that other inputs

cannot be assigned.

3.

Press the

OK

/

ENTER

button.

4.

Select each mode setting and input terminal

with the

1

or

2

cursor buttons.

5.

Press the

OK

/

ENTER

button.

6.

Repeat steps 2-5 until all items are set.

7.

After you complete this portion of the setup,

move the cursor to “

NEXT

” with the

3

,

4

,

1

,

and

2

cursor buttons and then press the

OK

/

ENTER

button to go to the next page.

FUNC INPUT SETUP 2

FUNC:MODE DIG HDMI C0MP V/S

TAPE:ANA

-

- -

1

CD/R:AUTO

5

- -

2

AUX2:ANA

-

- -

3

RETURN

BACK

EXIT

8.

Repeat steps 2-5 until all items are set.

After you complete this portion of the setup,

move the cursor to “

RETURN

” with

3

,

4

,

1

,

and

2

cursor buttons and press the

OK

/

ENTER

button.

To return to the Func Input Setup 1 menu from

the Func Input Setup 2 menu, move the cursor

to “

BACK

” with the

3

,

4

,

1

, and

2

cursor


OK

/

ENTER

button.

Note:

• Assignments cannot be made in sections with a

✽

mark.

1-2

7.1 CH INPUT SETUP

This menu is for adjusting the speaker levels for 7.1-

channel input sources.

Here you will adjust the volume for each channel so

that they are all heard by the listener at the same

level.

1.

Select “

7.1 CH INPUT SETUP

” from the

1.INPUT SETUP menu with the

3

or

4

cursor


OK

/

ENTER

button.

7.1CH INPUT SETUP

VIDEO-IN

:

LAST

FRONT L

:

0dB

CENTER

:

0dB

FRONT R

:

0dB

SURR.R

:

0dB

SURR.B R

:

0dB

SURR.B L

:

0dB

SURR. L

:

0dB

SUB W

:

0dB

RETURN

NEXT

EXIT

2.

Select “

VIDEO-IN

” with the

3

or

4

cursor

buttons.

3.

Using the

1

or

2

cursor buttons, select the

video input source to be played through the

MONITOR OUT jack.

The input source is switched by pressing the

1

or

2

cursor buttons as follows;

LAST

↔

TV

↔

DVD

↔

VCR1

↔

DSS

↔

AUX1

↔

V-OFF

↔

LAST

↔

...

Notes:

•

When “

LAST

” is selected, the source is set to the

source selected before the 7.1 ch input menu was

activated.

• When

“

V-OFF

” is selected,

no signal is emitted from

MONITOR OUT jack.

4.

Select desired channel with the

3

or

4

cursor

buttons.

5.

Using the

1

or

2

cursor buttons, adjust the

volume level of each channel.

Move the cursor to “

RETURN

” with the

3

,

4

,

1

, and

2

cursor buttons, and press the

OK

/

ENTER

button to

go to the 1.INPUT SETUP menu.

Note:

• The volume level can be set between -12 dB and

+12 dB in 1 dB increments on all channels except the

subwoofer (SUB W), which can be set from -18dB

to +12 dB in 1 dB increments.

Marantz SR7002 User Manual - English - Page 46

Func Input Setup, Assignable Digital Input, 1 Ch Input Setup - aux jack

Page 46 highlights