Maytag MDB7609AWB Installation Instructions - Page 13

Determine - black

Get Maytag MDB7609AWB - 24inch Tall Tub Dishwasher PDF manuals and user guides
UPC - 883049182827
View all Maytag MDB7609AWB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Wiring configuration Determine Cabinet Opening black _ ground W!re _ black ground connector If needed, see website for animated representation of this step. Visit www.maytag.eom under FAQ tab. J Power cord - Secure cord on conduit connector 0 Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and the highest point on the floor). Refer to "Dishwasher Height Adjustment Chart" for wheel position and the number of turns needed. Tighten strain relief screws to secure cord. ) Cabinet " Opening height 337i8 (860 I Wheel position remo_e 34 (86 4cm) ! 1 34 1/4, (87 cm). 2 . 34 1/2" (87,6 cm) 3 Number of turns on front leg A!! the Way Up . 10 I 5 .... m : 0 NOTE: If the minimum cabinet opening height is less than 34"(86.4 cm), the rear wheels can be removed for additional clearance. This will allow the dishwasher to fit into a 33 7/8" (86 cm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Wheels and legs are preset at the factory for 34 1/2" [87.6 cm].) Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. Use 1/4" nut driver and previously removed screw to secure cover. NOTE: Do not plug into outlet until instructed to do so. ) Turn both leveler legs to the same height. Put wheels in the required position determined from "Dishwasher Height Adjustment Chart." 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Wiring
configuration
black _
black
ground
W!re _
ground
connector
If needed,
see website
for animated
representation
of
this step. Visit
www.maytag.eom
under
FAQ tab.
J
Power
cord
- Secure
cord
on
conduit
connector
0
)
Tighten
strain
relief screws
to secure
cord.
Place wires
inside
terminal
box.
Insert
tabs
on left side
of cover.
Make sure wires
are tucked
inside
box.
Close
cover
ensuring
wires
are not
pinched.
Use
1/4" nut driver
and previously
removed
screw
to secure
cover.
NOTE: Do not
plug
into
outlet
until
instructed
to do so.
Determine
Cabinet Opening
Measure
height
of cabinet
opening
from
underside
of
countertop
to floor
where
dishwasher
will
be installed
(you will
need to measure
the
lowest
point
on the
underside
of the countertop
and the
highest
point
on the
floor).
Refer to "Dishwasher
Height
Adjustment
Chart"
for wheel
position
and the
number
of turns
needed.
Cabinet
"
Wheel
Number
of turns
Opening
height
position
on
front
leg
I
337i8
(860
remo_e
A!! the Way Up
34
(86 4cm)
!
1
.
10
I
34 1/4, (87 cm).
2
5
....
.
m
34 1/2" (87,6 cm)
3
:
0
NOTE: If the
minimum
cabinet
opening
height
is less than
34"(86.4
cm),
the
rear wheels
can
be removed
for
additional
clearance.
This
will
allow
the dishwasher
to fit
into
a 33 7/8"
(86 cm)
high cabinet
opening,
but the
dishwasher
will
be more
difficult
to move.
(Measurements
are approximate.
Wheels
and legs are preset
at the
factory
for 34 1/2" [87.6 cm].)
)
Turn
both
leveler
legs to the
same
height.
Put wheels
in
the
required
position
determined
from
"Dishwasher
Height
Adjustment
Chart."
13