Netgear WNAP210 WNAP210 Reference Manual - Page 96

Con the WNAP210 access point AP2 on LAN Segment 2 in Point-to-Point Bridge

Get Netgear WNAP210 - ProSafe Wireless-N - Wireless Access Point PDF manuals and user guides
UPC - 606449062694
View all Netgear WNAP210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

ProSafe Wireless-N Access Point WNAP210 Reference Manual Figure 4-7 3. Configure the WNAP210 access point (AP2) on LAN Segment 2 in Point-to-Point Bridge mode. AP1 must have AP2's MAC address in its Remote MAC Address field, and AP2 must have AP1's MAC address in its Remote MAC Address field. 4. Configure and verify the following parameters for both access points: • Verify that both access points are configured to operate in the same LAN network address range as the LAN devices. • Both use the same ESSID (Extended Service Set Identification), channel, authentication mode, if any, and security settings if security is in use. 4-12 v1.0 March 2009 Advanced Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 4-7
ProSafe Wireless-N Access Point WNAP210 Reference Manual
4-12
Advanced Configuration
v1.0 March 2009
3.
Configure the WNAP210 access point (AP2) on LAN Segment 2 in Point-to-Point Bridge
mode.
AP1 must have AP2’s MAC address in its Remote MAC Address field, and AP2 must have
AP1’s MAC address in its Remote MAC Address field.
4.
Configure and verify the following parameters for both access points:
•
Verify that both access points are configured to operate in the same LAN network address
range as the LAN devices.
•
Both use the same ESSID (Extended Service Set Identification), channel, authentication
mode, if any, and security settings if security is in use.