Oki C830dn User Guide - Page 72

Replace the four image drums, complete with their toner cartridges, into the printer

Get Oki C830dn PDF manuals and user guides View all Oki C830dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

4. Locate the two fasteners (a) at each side of the belt and the lifting bar (b) at the front end. a b a 5. Turn the two fasteners 90° to the left. This will release the belt from the printer chassis. 6. Pull the lifting bar (b) upwards so that belt tilts up towards the front, and withdraw the belt unit from the printer. 7. Lower the new belt unit into place, with the lifting bar at the front and the drive gear towards the rear of the printer. Locate the drive gear into the gear inside the printer by the rear left corner of the unit, and lower the belt unit flat inside the printer. 8. Turn the two fasteners (a) 90° to the right until they lock. This will secure the belt unit in place. 9. Replace the four image drums, complete with their toner cartridges, into the printer in the same sequence as they came out: cyan (nearest the rear), magenta, yellow and black (nearest the front). 10. Finally, close the top cover and press down firmly at both sides so that the cover latches closed. Replacing consumable items > 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Replacing consumable items > 72
4.
Locate the two fasteners (a) at each side of the belt and the lifting bar (b) at the
front end.
5.
Turn the two fasteners 90° to the left. This will release the belt from the printer
chassis.
6.
Pull the lifting bar (b) upwards so that belt tilts up towards the front, and withdraw
the belt unit from the printer.
7.
Lower the new belt unit into place, with the lifting bar at the front and the drive gear
towards the rear of the printer. Locate the drive gear into the gear inside the printer
by the rear left corner of the unit, and lower the belt unit flat inside the printer.
8.
Turn the two fasteners (a) 90° to the right until they lock. This will secure the belt
unit in place.
9.
Replace the four image drums, complete with their toner cartridges, into the printer
in the same sequence as they came out: cyan (nearest the rear), magenta, yellow
and black (nearest the front).
10.
Finally, close the top cover and press down firmly at both sides so that the cover
latches closed.
a
a
b