Oki C830dn User Guide - Page 73

will be very hot. Handle the fuser with extreme care, holding it only

Get Oki C830dn PDF manuals and user guides View all Oki C830dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

FUSER REPLACEMENT The fuser is located inside the printer just behind the four image drum units. WARNING! If the printer has recently been powered on, some fuser components will be very hot. Handle the fuser with extreme care, holding it only by its handle, which will only be mildly warm to the touch. A warning label clearly indicates the area. If in doubt, switch the printer off and wait at least 10 minutes for the fuser to cool before opening the printer cover. Switch off the printer. 1. Press the cover release and open the printer's top cover fully. 2. Identify the fuser handle (a) on the top of the fuser unit. a b 3. Pull the fuser retaining lever (b) towards the front of the printer so that it is fully upright. 4. Holding the fuser by its handle (a), lift the fuser straight up and out of the printer. If the fuser is still warm, place it on a flat surface which will not be damaged by heat. 5. Remove the new fuser from its packaging and remove the transit material. 6. Holding the new fuser by its handle, make sure that it is the correct way round. The retaining lever (b) should be fully upright. 7. Lower the fuser into the printer. Replacing consumable items > 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Replacing consumable items > 73
F
USER
REPLACEMENT
The fuser is located inside the printer just behind the four image drum units.
Switch off the printer.
1.
Press the cover release and open the printer’s top cover fully.
2.
Identify the fuser handle (a) on the top of the fuser unit.
3.
Pull the fuser retaining lever (b) towards the front of the printer so that it is fully
upright.
4.
Holding the fuser by its handle (a), lift the fuser straight up and out of the printer. If
the fuser is still warm, place it on a flat surface which will not be damaged by heat.
5.
Remove the new fuser from its packaging and remove the transit material.
6.
Holding the new fuser by its handle, make sure that it is the correct way round. The
retaining lever (b) should be fully upright.
7.
Lower the fuser into the printer.
WARNING!
If the printer has recently been powered on, some fuser components
will be very hot. Handle the fuser with extreme care, holding it only by
its handle, which will only be mildly warm to the touch. A warning
label clearly indicates the area. If in doubt, switch the printer off and
wait at least 10 minutes for the fuser to cool before opening the
printer cover.
a
b