Panasonic PT-D6000ULK Functional Instructions - Page 47

REMOTE 2 IN terminal, Technical Information, Pin assignments and control

Get Panasonic PT-D6000ULK - XGA DLP Projector PDF manuals and user guides
UPC - 791871111871
View all Panasonic PT-D6000ULK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Technical Information REMOTE 2 IN terminal Using the REMOTE 2 IN terminal provided on the connection terminals of the main unit, it is possible to operate the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be received. Remote terminal External control Remote terminal/External control Standby ON LAMP Projector set up in a meeting room J Pin assignments and control Control panel located in a different room Pin No. 1 2 3 4 5 6 7 8 9 Signal name GND POWER RGB1 RGB2 VIDEO S-VIDEO DVI-D SHUTTER RST / SET Open (H) OFF Other Other Other Other Other OFF Controlled by remote control Short (L) GND ON RGB1 RGB2 VIDEO S-VIDEO DVI-D ON Controlled by external contact NOTE: • The following buttons on the remote control and the operation area of the projector can no longer be operated when pins 1 and 9 are shortened: POWER button and SHUTTER button. Neither will it be possible to use the RS-232C commands or network functions corresponding to these functions. • If you short pin 1 and pin 9, and also short one of the pins from 3 to 7 and pin 1, then the following buttons on the projector operating area and the remote control can no longer be operated: POWER, RGB1, RGB2, DVI-D, VIDEO, S-VIDEO, SDI and SHUTTER buttons. Neither will it be possible to use the RS-232C commands or network functions corresponding to these functions. Appendix ENGLISH - 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Technical Information
E
NGLISH - 47
Appendix
Using the
REMOTE 2 IN
terminal provided on the connection terminals of the main unit, it is possible to operate the
projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be
received.
Pin assignments and control
REMOTE 2 IN terminal
Pin No.
Signal name
Open (H)
Short (L)
1
GND
GND
2
POWER
OFF
ON
3
RGB1
Other
RGB1
4
RGB2
Other
RGB2
5
VIDEO
Other
VIDEO
6
S-VIDEO
Other
S-VIDEO
7
DVI-D
Other
DVI-D
8
SHUTTER
OFF
ON
9
RST / SET
Controlled by remote
control
Controlled by external
contact
NOTE:
•
The following buttons on the remote control and the operation area of the projector can no longer be operated when pins
1 and 9 are shortened:
POWER
button and
SHUTTER
button. Neither will it be possible to use the RS-232C commands
or network functions corresponding to these functions.
•
If you short pin 1 and pin 9, and also short one of the pins from 3 to 7 and pin 1, then the following buttons on the projector
operating area and the remote control can no longer be operated:
POWER
,
RGB1
,
RGB2
,
DVI-D
,
VIDEO
,
S-VIDEO
,
SDI
and
SHUTTER
buttons. Neither will it be possible to use the RS-232C commands or network functions corresponding to
these functions.
Standby
ON
Remote
terminal
External
control
LAMP
Remote terminal/External control
Projector set up in a meeting room
Control panel located in a different room