Sony DCR-TRV10 Service Manual - Page 94
INITIALIZATION OF B, C, D, E, F DATA, Initializing Method, Modifying Method - camcorder
View all Sony DCR-TRV10 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 94 highlights
1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA 1-2-1. INITIALIZATION OF C PAGE DATA 1. Initializing the C Page Data Note: If the C page data has been initialized, the following adjustments need to be performed again. 1) Modification of C page data 2) Servo and RF system adjustments 3) Video system adjustments 4) IR transmitter adjustments Adjusting page Adjusting Address C 10 to DF Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 80, set data: 0C, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 80, and check that the data changes to "1C". 4) Perform "Modification of C Page Data". 2. Modification of C Page Data If the C page data has been initialized, change the data of the "Fixed data-2" address shown in the following table by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate. 3) When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. Processing after Completing Modification of C Page data 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, and set data: 29, and press the PAUSE button of the adjustment remote commander. 3. C Page Table Note: Fixed data-1 : Initialized data. (Refer to "1. Initializing the C Page Data".) Fixed data-2 : Modified data. (Refer to "2. Modification of C Page Data".) Address Initial value Remark NTSC PAL 00 to 0F 10 EE EE Switching position adj. 11 00 00 12 EE EE 13 00 00 14 Fixed data-1 15 (Initialized data) 16 E0 E0 Cap FG duty adj. 17 E0 E0 T reel FG duty adj. 18 2A 2A AEQ adj. 19 2A 2A 1A Fixed data-1 1B 33 33 AEQ adj. 1C 33 33 1D Fixed data-1 1E 25 25 AGC center level adj. 1F 3E 3E PLL f0 adj. 20 3E 3E 21 CA CA APC adj. 22 99 99 LPF f0 adj. 23 Fixed data-1 24 (Initialized data) 25 88 88 S VIDEO OUT Y level adj. 26 E3 E3 S VIDEO OUT chroma level adj. 27 A1 A1 S VIDEO OUT chroma level adj. 28 8A 8A IR video carrier freq. adj. 29 2D 2D IR video deviation adj. 2A 52 52 IR audio deviation adj. 2B 04 04 Chroma BPF f0 adj. 2C Fixed data-2 2D Fixed data-1 2E Fixed data-2 2F (Modified data, copy the data built in 30 the same model.) 31 Fixed data-1 32 (Initialized data) 33 34 Fixed data-2 35 Fixed data-1 36 (Initialized data) 37 38 00 00 Emergency memory address 39 00 00 3A 00 00 3B 00 00 3C 00 00 3D 00 00 3E 00 00 3F 00 00 40 00 00 5-8