TEAC DP-004 DP-004 Owners Manual (English) - Page 55

Monitoring the input signal, Setting the monitoring mode

Get TEAC DP-004 PDF manuals and user guides View all TEAC DP-004 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

6-Basic Recording selected as the INPUT A input source in step 2 above, set the MIC/LINE-GUITAR switch on the left side panel appropriately. Set it to GUITAR when connecting an electric guitar or electric bass directly. Set it to MIC/LINE when inputting a mic or line signal. TIP When connecting an electric-acoustic guitar with a built-in preamp or an active electric guitar, as well as when connecting an electric guitar with effect boxes between it and this unit, set the MIC/LINE-GUITAR switch to MIC/LINE. Monitoring the input signal When an input source is set as the INPUT A or INPUT B connector on the rear panel, regardless of the REC key setting, the input signal is always sent to the stereo bus, so you can always monitor the input signal. When an input source is set to a front panel built-in mic, the input signal is sent to the stereo bus and can be monitored only when the REC indicator light for the track that is set to record the built-in mic is blinking (during record standby) or lit (while recording). You cannot monitor the built-in mic input when the REC indicator is not lit. NOTE When an input source is set as the INPUT A or INPUT B connector, during playback, the sounds of the playback signal and the input source are mixed and can be heard through headphones or a monitoring system connected to the /LINE OUT connector. Setting the monitoring mode The monitoring mode can be set for the signals input on the INPUT A and INPUT B channels. 1 When the transport is stopped and the Home Screen is open, press the INPUT SETTING key to open the INPUT SETTING screen. 2 Use the F3 (§) and F4 (¶) keys to select the MODE item value, and turn the DATA wheel to select the TASCAM DP-004 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
6–Basic Recording
TASCAM
DP-004
55
selected as the
INPUT A
input source in step 2 above,
set the
MIC/LINE–GUITAR
switch on the left side
panel appropriately. Set it to
GUITAR
when connect-
ing an electric guitar or electric bass directly. Set it
to
MIC/LINE
when inputting a mic or line signal.
TIP
When connecting an electric-acoustic guitar with a
built-in preamp or an active electric guitar, as well as
when connecting an electric guitar with effect boxes
between it and this unit, set the MIC/LINE–GUITAR
switch to MIC/LINE.
Monitoring the input signal
When an input source is set as the
INPUT A
or
INPUT
B
connector on the rear panel, regardless of the
REC
key setting, the input signal is always sent to the
stereo bus, so you can always monitor the input
signal.
When an input source is set to a front panel built-in
mic, the input signal is sent to the stereo bus and
can be monitored only when the
REC
indicator light
for the track that is set to record the built-in mic
is blinking (during record standby) or lit (while
recording). You cannot monitor the built-in mic
input when the
REC
indicator is not lit.
NOTE
When an input source is set as the
INPUT A
or
INPUT B
connector, during playback, the sounds of the playback
signal and the input source are mixed and can be heard
through headphones or a monitoring system connected
to the
/
LINE OUT
connector.
Setting the monitoring mode
The monitoring mode can be set for the signals input
on the
INPUT A
and
INPUT B
channels.
1 When the transport is stopped and the Home
Screen is open, press the
INPUT SETTING
key to open
the
INPUT SETTING
screen.
2 Use the
F3
(
§
) and
F4
(
) keys to select the
MODE
item value, and turn the
DATA
wheel to select the