Toshiba 24V4260U User Guide - Page 52

o Tuning

Get Toshiba 24V4260U PDF manuals and user guides View all Toshiba 24V4260U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

52 Setting up your TV Storing channels in memory (optional) 4 Highlight ANT/CABLE In and press the ( / arrow) buttons to select the input source (Cable or Antenna). (Sample Image) Selecting the ANT/CABLE input source 5 To save your new settings, highlight Done, and then press the OK button. To revert to your original settings, highlight Cancel, and then press the OK button. Storing channels in memory (optional) To make sure your TV stops only on the channels you want when you press the CH Up/Down arrow buttons on the remote control or the control panel, store those channels in the TV's memory. Auto Tuning You can configure the TV to detect all active channels in your area and store them in its memory. Then you can manually store or skip individual channels from memory. NOTE ❖ You must configure the antenna/cable input source first. ❖ The automatic channel programming process will erase channels that were previously programmed into the TV's memory. ❖ To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. ❖ Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Configure the antenna input source, if you have not already done, see "ANT/CABLE IN" on page 51. 2 Press the MENU button to open the Setup menu.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
52
Se
tt
ing up you
r
TV
Storing channels in memory (optional)
4
Highlight
ANT/CABLE In
and press the (
arrow) buttons
to select the input source (
Cable
or
Antenna
).
(Sample Image) Selecting the ANT/CABLE input source
5
To save your new settings, highlight
Done
, and then press the
OK
button. To revert to your original settings, highlight
Cancel
, and then press the
OK
button.
S
t
o
r
ing channels in memo
r
y (op
t
ional)
To make sure your TV stops only on the channels you want when
you press the
CH Up/Down
arrow buttons on the remote control or
the control panel, store those channels in the TV’s memory.
Au
t
o Tuning
You can configure the TV to detect all active channels in your area
and store them in its memory. Then you can manually store or skip
individual channels from memory.
❖
You must configure the antenna/cable input source first.
❖
The automatic channel programming process will erase
channels that were previously programmed into the TV’s
memory.
❖
To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
❖
Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when the
antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should not
have to repeat the programming process again unless your
Cable TV service lineup changes significantly.
To program channels automatically:
1
Configure the antenna input source, if you have not already
done, see
“ANT/CABLE IN” on page 51
.
2
Press the
MENU
button to open the
Setup
menu.
NOTE