ViewSonic PJD7583wi PJD7383, PJD7383I, PJD7583W, PJD7583WI User Guide (English - Page 43

Controlling the projector through a LAN, environment

Get ViewSonic PJD7583wi PDF manuals and user guides
UPC - 766907511123
View all ViewSonic PJD7583wi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Controlling the projector through a LAN environment You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network. Internet Cable/ADSL modem Wired LAN connection If you are in a DHCP environment: 1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router. 2. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the SYSTEM SETUP: Basic menu is highlighted. 3. Press to highlight LAN Control Settings and press MODE/ENTER on the projector or ENTER on the remote control. The LAN Control Settings page is displayed. 4. Highlight Wired LAN and press MODE/ENTER on the projector or ENTER on the remote control. 5. Make sure the Status is Connect. 6. Press to highlight DHCP and press / to select On. 7. Press to highlight Apply and press MODE/ENTER on the projector or ENTER on the remote control. 8. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row. • If the Projector IP Address still does not appear, contact your network administrator. • If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again. • If you wish to connect to the projector in its standby mode, be sure you have selected RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information when the projector is on. If you are in a non-DHCP environment: 1. Repeat steps 1-5 above. 2. Press to highlight DHCP and press / to select Off. 3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings. Operation 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Operation
39
Controlling the projector through a LAN
environment
You can manage and control the projector from one or more remote computers when they
are properly connected to the same local area network.
Wired LAN connection
If you are in a DHCP environment:
1.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port on your Ethernet or router.
2.
Press
MENU/EXIT
on the projector or
Menu
on the remote control and then press
/
until the
SYSTEM SETUP: Basic
menu is highlighted.
3.
Press
to highlight
LAN Control Settings
and press
MODE/ENTER
on the
projector or
ENTER
on the remote control. The
LAN Control Settings
page is
displayed.
4.
Highlight
Wired LAN
and press
MODE/ENTER
on the projector or
ENTER
on the
remote control.
5.
Make sure the
Status
is
Connect
.
6.
Press
to highlight
DHCP
and press
/
to select
On
.
7.
Press
to highlight
Apply
and press
MODE/ENTER
on the projector or
ENTER
on the remote control.
8.
Please wait for around 15 - 20 seconds, and then re-enter the
Wired LAN
page. The
IP Address
,
Subnet Mask
,
Default Gateway
, and
DNS
settings will be displayed.
Note down the IP address displayed in the
IP Address
row.
•
If the Projector IP Address still does not appear, contact your network administrator.
•
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
•
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
If you are in a non-DHCP environment:
1.
Repeat steps 1-5 above.
2.
Press
to highlight
DHCP
and press
/
to select
Off
.
3.
Contact your ITS administrator for information on the
IP Address
,
Subnet Mask
,
Default Gateway
, and
DNS
settings.
Cable/ADSL
modem
Internet