Yamaha SP2060 SP2060 V1.2 Owners Manual - Page 26

Output EQ, Bypass, Type, Q, Freq, or Gain parameter.

Get Yamaha SP2060 PDF manuals and user guides View all Yamaha SP2060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Foreword Introduction to the SP2060 The Controls and Connectors Panel Operation 1. Press the [EQ] key repeatedly to select the EQ display. IN A ON/OFF = ON 2. Press the [SEL] key for the target channel. The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. Pressing the [SEL] keys for channels A and B will turn on the [SEL] key LEDs and select channel SUM. IN SUM ON/OFF = ON 3. Press the [EQ], [BACK] or [NEXT] key to display the On/Off parameter. 4. Press the [▲INC] key to set the On/Off parameter to On to apply EQ to the signal. Press the [▼DEC] key to set the On/Off parameter to Off to not process the signal. 5. Press the [BACK] or [NEXT] key to select the Bypass, Type, Q, Freq, or Gain parameter. IN SUM BAND 2 Q = 0.125 6. Pressing the [EQ] key repeatedly will scroll the bands from 1 through 8. IN SUM BAND 3 Q = 0.125 7. Press the [▲INC]/[▼DEC] keys to select the value. Output EQ You can apply a 6-band EQ to Output channels 1-6. Set the On/Off parameter to On to apply EQ to the signal, and Off to not process the signal. The parameters are the same as for the input EQ. You can set the following parameters for each band. Parameter Range BYPASS ON/OFF TYPE Q PEQ L.SHELF 6dB/Oct L.SHELF 12dB/Oct H.SHELF 6dB/Oct H.SHELF 12dB/Oct HPF LPF APF 1st APF 2nd Horn 63.0-0.1 FREQ (Frequency) GAIN 20.0Hz-20.0kHz -18dB through +18.00dB Function Sets the bypass for each frequency range to On or Off. Selects a type of filter. Specifies the width of each frequency range. Specifies the frequency of each band. Sets the gain of the target frequency. • APF (All Pass Filter) This filter passes all ranges of frequency, but changes only the phase. It is used to align the phase in the crossover range. APF 1st rotates the phase by 0 through 180 degrees, and APF 2nd rotates the phase by 0 through 360 degrees. APF 2nd requires the Q setting. • Horn A horn speaker typically features a roll-off in the higher frequency component. Horn EQ corrects this characteristics. For this purpose, the gain is limited to 0dB or higher, and the frequency to 500Hz or higher. Panel Operation Network Settings References 26 SP2060 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings
References
Panel Operation
Introduction
to the SP2060
The Controls
and Connectors
26
1.
Press the [EQ] key repeatedly to select the
EQ display.
2.
Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
Pressing the [SEL] keys for channels A and B will turn on
the [SEL] key LEDs and select channel SUM.
3.
Press the [EQ], [BACK] or [NEXT] key to
display the On/Off parameter.
4.
Press the [
▲
INC] key to set the On/Off
parameter to On to apply EQ to the signal.
Press the [
▼
DEC] key to set the On/Off
parameter to Off to not process the signal.
5.
Press the [BACK] or [NEXT] key to select the
Bypass, Type, Q, Freq, or Gain parameter.
6.
Pressing the [EQ] key repeatedly will scroll
the bands from 1 through 8.
7.
Press the [
▲
INC]/[
▼
DEC] keys to select the
value.
Output EQ
You can apply a 6-band EQ to Output channels 1–6.
Set the On/Off parameter to On to apply EQ to the signal,
and Off to not process the signal.
The parameters are the same as for the input EQ.
You can set the following parameters for each band.
•
APF (All Pass Filter)
This filter passes all ranges of frequency, but changes only
the phase. It is used to align the phase in the crossover
range.
APF 1st rotates the phase by 0 through 180 degrees, and
APF 2nd rotates the phase by 0 through 360 degrees. APF
2nd requires the Q setting.
• Horn
A horn speaker typically features a roll-off in the higher
frequency component.
Horn EQ corrects this characteristics. For this purpose,
the gain is limited to 0dB or higher, and the frequency to
500Hz or higher.
IN A
ON/OFF =
ON
IN SUM
ON/OFF =
ON
IN SUM
BAND 2
Q
=
0.125
IN SUM
BAND 3
Q
=
0.125
Parameter
Range
Function
BYPASS
ON/OFF
Sets the bypass
for each
frequency range
to On or Off.
TYPE
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
APF 1st
APF 2nd
Horn
Selects a type of
filter.
Q
63.0–0.1
Specifies the
width of each
frequency range.
FREQ
(Frequency)
20.0Hz–20.0kHz
Specifies the
frequency of each
band.
GAIN
–18dB through
+18.00dB
Sets the gain of
the target
frequency.