Yamaha SP2060 SP2060 V1.2 Owners Manual - Page 47

Status messages, Troubleshooting

Get Yamaha SP2060 PDF manuals and user guides View all Yamaha SP2060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Foreword Introduction to the SP2060 The Controls and Connectors References Status messages Message Connecting Download Success Downloading File Operating Network Setup Panel Locked Panel Unlocked Scene Recalling Scene Storing Cannot Recall Cannot Store NO X-OVER NO LIMITER Protected NO ROUTING NO LEVEL Network Busy Synchronizing Scene Deleting Meaning Connecting to the network. The program has been successfully updated. Program update in progress. Do NOT turn power off while the unit displays this message. A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off while the unit displays this message. Preparing network connection. The User Lock function is engaged. The panel controls do not work. The User Lock function has been disengaged. Panel operation is now possible. Scene recall in progress. Scene store in progress. Do NOT turn power off while the unit displays this message. Recalling scenes or libraries is disabled. The scene store is disabled. Input channels do not feature the X-Over parameter. Input channels do not feature the Limiter parameter. You cannot edit or delete protected scenes. Input channel SUM does not feature the Routing parameter. Input channel SUM does not feature the Level parameter. There is too much network traffic. Communication is very slow. Data is being received from the computer. Do NOT turn power off while the unit displays this message. Deleting a scene. Do NOT turn power off while the unit displays this message. * Do NOT turn off the power to the SP2060 while the unit displays the message "DO NOT TURN OFF!" at the bottom of the display. Troubleshooting Symptom No communication between the SP2060 and the DME Designer application software. No audio output. The parameters cannot be edited. Possible Causes The connection cable is not connected properly. The computer's Ethernet port is not functioning properly. The DME-N Network driver has not been installed. The Mute function is turned on. The output level is set too low. The User Lock function is turned on. Possible Solutions Make sure that the cable is properly connected. Refer to the DME Designer Installation Guide. Install and set up the DME-N Network driver. Turn off the Mute function (see page 38). Increase the output level (see page 24). Turn off the User Lock function (see page 34). Panel Operation Network Settings References SP2060 Owner's Manual 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings
Panel Operation
References
SP2060 Owner’s Manual
47
Status messages
* Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display.
Troubleshooting
Message
Meaning
Connecting
Connecting to the network.
Download Success
The program has been successfully updated.
Downloading
Program update in progress. Do NOT turn power off while the unit displays this message.
File Operating
A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off
while the unit displays this message.
Network Setup
Preparing network connection.
Panel Locked
The User Lock function is engaged. The panel controls do not work.
Panel Unlocked
The User Lock function has been disengaged. Panel operation is now possible.
Scene Recalling
Scene recall in progress.
Scene Storing
Scene store in progress. Do NOT turn power off while the unit displays this message.
Cannot Recall
Recalling scenes or libraries is disabled.
Cannot Store
The scene store is disabled.
NO X-OVER
Input channels do not feature the X-Over parameter.
NO LIMITER
Input channels do not feature the Limiter parameter.
Protected
You cannot edit or delete protected scenes.
NO ROUTING
Input channel SUM does not feature the Routing parameter.
NO LEVEL
Input channel SUM does not feature the Level parameter.
Network Busy
There is too much network traffic. Communication is very slow.
Synchronizing
Data is being received from the computer. Do NOT turn power off while the unit displays this message.
Scene Deleting
Deleting a scene. Do NOT turn power off while the unit displays this message.
Symptom
Possible Causes
Possible Solutions
No communication between the
SP2060 and the DME Designer
application software.
The connection cable is not connected properly.
Make sure that the cable is properly connected.
The computer's Ethernet port is not functioning
properly.
Refer to the DME Designer Installation Guide.
The DME-N Network driver has not been
installed.
Install and set up the DME-N Network driver.
No audio output.
The Mute function is turned on.
Turn off the Mute function (see page 38).
The output level is set too low.
Increase the output level (see page 24).
The parameters cannot be edited.
The User Lock function is turned on.
Turn off the User Lock function (see page 34).