eMachines D620 Service Guide - Page 82

Index of Error Messages - cmos battery

Get eMachines D620 PDF manuals and user guides View all eMachines D620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Index of Error Messages Error Message List Error Messages Stuck Key System CMOS checksum bad - Default configuration used Real time clock error Previous boot incomplete - Default configuration used Invalid System Configuration Data Operating system not found Power-on indicator turns off and LCD is blank. Power-on indicator turns on and LCD is blank. Power-on indicator turns on and LCD is blank. But you can see POST on an external CRT. Power-on indicator turns on and a blinking cursor shown on LCD during POST. Failure Fixed Disk Check or do the following in sequence: See "Keyboard or Auxiliary Input Device Check" on page 88. • RTC battery. • Run the BIOS Setup Utility to reconfigure the system time, then reboot system. • RTC battery • Run the BIOS Setup Utility to reconfigure system time, then reboot system. • Mainboard • Run "Load Setup Defaults" in BIOS Setup Utility. • RTC battery • Mainboard • Run "Load Setup Defaults" in BIOS Setup Utility. • Mainboard • Run the BIOS Setup Utility to check if the fixed disk and drive A are properly identified. • CD/DVD-ROM drive • Hard disk drive • Mainboard • Power source (battery pack and power adapter.) See "Power System Check" on page 89. • Ensure every connector is connected tightly and correctly. • Reconnect the DIMM • Mainboard • Power source (battery pack and power adapter.) See "Power System Check" on page 89. • Reconnect the LCD connector • Hard disk drive • LCD cable • LCD inverter • LCD • Mainboard • Reconnect the LCD connectors. • LCD cable • LCD inverter • LCD • Mainboard • Ensure every connector is connected tightly and correctly. • Mainboard • Reconnect the hard disk drive connector. • Run "Load Setup Defaults" in BIOS Setup Utility. • Hard disk drive • Mainboard 92 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
92
Chapter 4
Index of Error Messages
Error Message List
Error Messages
Check or do the following in sequence:
Stuck Key
See “Keyboard or Auxiliary Input Device Check” on page 88.
System CMOS checksum bad - Default
configuration used
•
RTC battery.
•
Run the BIOS Setup Utility to reconfigure the system time,
then reboot system.
Real time clock error
•
RTC battery
•
Run the BIOS Setup Utility to reconfigure system time, then
reboot system.
•
Mainboard
Previous boot incomplete - Default
configuration used
•
Run “Load Setup Defaults” in BIOS Setup Utility.
•
RTC battery
•
Mainboard
Invalid System Configuration Data
•
Run “Load Setup Defaults” in BIOS Setup Utility.
•
Mainboard
Operating system not found
•
Run the BIOS Setup Utility to check if the fixed disk and drive
A are properly identified.
•
CD/DVD-ROM drive
•
Hard disk drive
•
Mainboard
Power-on indicator turns off and LCD is
blank.
•
Power source (battery pack and power adapter.) See “Power
System Check” on page 89.
•
Ensure every connector is connected tightly and correctly.
•
Reconnect the DIMM
•
Mainboard
Power-on indicator turns on and LCD
is blank.
•
Power source (battery pack and power adapter.) See “Power
System Check” on page 89.
•
Reconnect the LCD connector
•
Hard disk drive
•
LCD cable
•
LCD inverter
•
LCD
•
Mainboard
Power-on indicator turns on and LCD
is blank. But you can see POST on an
external CRT.
•
Reconnect the LCD connectors.
•
LCD cable
•
LCD inverter
•
LCD
•
Mainboard
Power-on indicator turns on and a
blinking cursor shown on LCD during
POST.
•
Ensure every connector is connected tightly and correctly.
•
Mainboard
Failure Fixed Disk
•
Reconnect the hard disk drive connector.
•
Run “Load Setup Defaults” in BIOS Setup Utility.
•
Hard disk drive
•
Mainboard