3Com 5500-EI Getting Started Guide - Page 62

Connecting the Workstation to the Switch, Setting Up the Switch with IP Information, <500G-EI&gt - default ip

Get 3Com 5500-EI - Switch PWR PDF manuals and user guides
UPC - 662705498997
View all 3Com 5500-EI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

62 CHAPTER 3: SETTING UP FOR MANAGEMENT Connecting the Workstation to the Switch 1 Connect the workstation to the console port using the console cable as shown in Figure 26. Figure 26 Connecting a Workstation to the Switch via the Console Port Workstation (with terminal emulation software installed) Console Cable Switch Console Port Connection To connect the cable: a Attach the RJ-45 connector on the cable to the switch's console port. b Attach the other end of the cable to the workstation and tighten the retaining screws on the cable to prevent it from loosening. 2 Open your terminal emulation software and configure the COM port settings to which you have connected the cable. Make sure that the settings match the switch's default settings, which are: ■ 19,200 baud (bits per second) ■ 8 data bits ■ no parity ■ 1 stop bit ■ no hardware flow control Refer to the terminal emulation software's documentation for more information about these settings. 3 Power up the switch. The switch performs its Power on Self Test (POST). Setting Up the Switch with IP Information To manually set up the switch with IP information using the command line interface, perform the following steps. 1 The command line interface login sequence begins as soon as the switch detects a connection to its console port. If the login prompt does not begin immediately, press Return a few times until it starts. 2 At the Username prompt, enter admin as your user name and press Return. At the password prompt press Return again. Either

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
62
C
HAPTER
3: S
ETTING
U
P
FOR
M
ANAGEMENT
Connecting the Workstation to the Switch
1
Connect the workstation to the console port using the console cable as
shown in Figure 26.
Figure 26
Connecting a Workstation to the Switch via the Console Port
To connect the cable:
a
Attach the RJ-45 connector on the cable to the switch’s console port.
b
Attach the other end of the cable to the workstation and tighten the
retaining screws on the cable to prevent it from loosening.
2
Open your terminal emulation software and configure the COM port
settings to which you have connected the cable. Make sure that the
settings match the switch’s default settings, which are:
■
19,200 baud (bits per second)
■
8 data bits
■
no parity
■
1 stop bit
■
no hardware flow control
Refer to the terminal emulation software’s documentation for more
information about these settings.
3
Power up the switch. The switch performs its Power on Self Test (POST).
Setting Up the Switch with IP Information
To manually set up the switch with IP information using the command
line interface, perform the following steps.
1
The command line interface login sequence begins as soon as the switch
detects a connection to its console port. If the login prompt does not
begin immediately, press
Return
a few times until it starts.
2
At the Username prompt, enter
admin
as your user name and press
Return
. At the password prompt press
Return
again. Either
<500G-EI>
Console Port
Connection
Workstation
(with terminal emulation
software installed)
Console Cable
Switch