3Com WX2200 Hardware Installation Guide - Page 18

Appearance, Meaning, WXR100 Status LEDs

Get 3Com WX2200 - Wireless LAN Controller PDF manuals and user guides
UPC - 662705511191
View all 3Com WX2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 CHAPTER 1: WX SWITCH OVERVIEW Table 5 WXR100 Status LEDs LED Power status Link (ports 1 and 2) Fn (port 1 only) MAP (port 2 only) Appearance Meaning Solid green The switch is receiving power. Unlit The switch is not receiving power. Solid green 100-Mbps link is operational. Solid amber 10-Mbps link is operational. Blinking green Traffic is active on the 100-Mbps link. Blinking amber Traffic is active on the 10-Mbps link. Solid green The switch is booting and is loading its configuration file. This LED state lasts for three seconds. Blinking green The switch is booting but the Fn switch is being pressed. The switch does not load its configuration file but instead contacts WX to request a configuration. This LED state lasts for three seconds. Unlit The switch has finished booting. Solid green For a MAP access point's active link, with PoE enabled, all the following are true: MAP access point has booted. MAP access point has received a valid configuration from the WX switch. Management link with an MAP access point is operational. Alternating green and MAP access point is booting with an amber image received from the WX switch. If the LED remains in this state indefinitely, the boot or configuration attempt has failed. Solid amber PoE is on but no MAP access point is connected to the link. Blinking amber MAP is not connected or is unresponsive, or there is a PoE problem. Unlit Port is not configured as a MAP access port, or PoE is off.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
18
C
HAPTER
1: WX S
WITCH
O
VERVIEW
Table 5
WXR100 Status LEDs
LED
Appearance
Meaning
Power status
Solid green
The switch is receiving power.
Unlit
The switch is not receiving power.
Link
(ports 1 and 2)
Solid green
100-Mbps link is operational.
Solid amber
10-Mbps link is operational.
Blinking green
Traffic is active on the 100-Mbps link.
Blinking amber
Traffic is active on the 10-Mbps link.
Fn
(port 1 only)
Solid green
The switch is booting and is loading its
configuration file. This LED state lasts
for three seconds.
Blinking green
The switch is booting but the Fn
switch is being pressed. The switch
does not load its configuration file but
instead contacts WX to request a
configuration.
This LED state lasts for three seconds.
Unlit
The switch has finished booting.
MAP (port 2 only)
Solid green
For a MAP access point’s active link,
with PoE enabled, all the following are
true:
MAP access point has booted.
MAP access point has received a valid
configuration from the WX switch.
Management link with an MAP access
point is operational.
Alternating green and
amber
MAP access point is booting with an
image received from the WX switch.
If the LED remains in this state
indefinitely, the boot or configuration
attempt has failed.
Solid amber
PoE is on but no MAP access point is
connected to the link.
Blinking amber
MAP is not connected or is
unresponsive, or there is a PoE
problem.
Unlit
Port is not configured as a MAP access
port, or PoE is off.