Asus Crosshair II Formula User Manual - Page 56
NVIDIA, nForce 780a SLI Serial ATA connectors, pin SATA1-4 [blue]; 7-pin SATA5-6 [black] - nvidia nforce sli
UPC - 610839160044
View all Asus Crosshair II Formula manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 56 highlights
2. ��N�V�ID�IA�® nForce 780a SLI Serial ATA connectors (7-pin SATA1-4 [blue]; 7-pin SATA5-6 [black]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk and optical disk drives. If you install Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 0+1, RAID 5, or JBOD configuration �th�r�o�u�g�h��t�h�e�o��n�b�o�a�r�d��N�V�I�D��IA�® nForce 780a SLI controller. GND RSATA_RXN1 RSATA_TXP1 GND RSATA_TXN1 RSATA_TXP1 GND GND RSATA_RXN2 RSATA_TXP2 GND RSATA_TXN2 RSATA_TXP2 GND SATA2 SATA1 GND RSATA_RXN3 RSATA_TXP3 GND RSATA_TXN3 RSATA_TXP3 GND GND RSATA_RXN4 RSATA_TXP4 GND RSATA_TXN4 RSATA_TXP4 GND CROSSHAIR II FORMULA ® SATA4 SATA3 GND RSATA_RXN5 RSATA_TXP5 GND RSATA_TXN5 RSATA_TXP5 GND GND RSATA_RXN6 RSATA_TXP6 GND RSATA_TXN6 RSATA_TXP6 GND SATA6 RESET CROSSHAIR II FORMULA SATA connectors SATA5 S�A�T�A��1�-�4��c�o�n�n�e�c�t�o�r�s�a�r�e��s�e�t �to� [�I�D�E b�y��d�e��fa��u�l�t.���I�f���y��o���u����i�n���t��e��n���d t�o��c�r�e�a�t�e� a Serial ATA RAID set using these connectors, set the SATA Operation Mode item to [RAID] in the BIOS. See section 4.5.6 MCP Storage Config for details. • SATA 5-6 connectors support AHCI mode and RAID mode only. Make sure to install the AHCI driver or RAID driver in the bundled support DVD before connecting devices to SATA 5-6 connectors. Otherwise, the devices will not work. • For RAID 5, use at least three hard disk drives. For RAID 0+1, use at least four hard disk drives. Use two to four Serial ATA hard disk drives for each RAID 0 or RAID 1 set. • Before creating a RAID set, refer to 5.4.2 NVIDIA® RAID configurations or the manual bundled in the motherboard support DVD. • You must install the Windows® XP Service Pack 1 before using Serial ATA hard disk drives. The Serial ATA RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is available only if you are using Windows® XP or later version. Connect the right-angle side of SATA signal cable to SATA device. Or you may connect the right-angle side of SATA cable to the onboard SATA port to avoid mechanical conflict with huge graphics cards. right angle side 2-30 Chapter 2: Hardware information