Asus SP97-XV User Manual - Page 29

ATX Power Switch / Soft Power Switch PWR SW

Get Asus SP97-XV PDF manuals and user guides View all Asus SP97-XV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

III. INSTALLATION (Connectors) III. INSTALLATION 12. Message LED Lead (MSG LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or waiting in the inbox). 13. SMI Suspend Switch Lead (SMI) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). 14. ATX Power Switch / Soft Power Switch (PWR SW) The system power is controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 15. Reset Switch Lead (RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. 16. System Power LED (PWR LED) This 3-pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 17. Keyboard Lock Switch Lead (KEYLOCK, 2 pins) This 2-pin connector connects to the case-mounted keyboard lock switch to allow keyboard locking. 18. Speaker Connector (SPEAKER) This 4-pin connector connects to the case-mounted speaker. R System Panel Connections Message LED SMI Lead ATX Power Switch* Reset SW +5 Volts MLED ExtSMI# Ground PWRBT# Ground ResetCon Ground +5 Volts PLED# KLock# Ground Power LED Keyboard Lock +5 Volts Ground Ground SPKR Speaker Connector * Requires an ATX power supply. ASUS SP97-XV User's Manual 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
ASUS SP97-XV User’s Manual
29
III. INSTALLATION
(Connectors)
III.
INSTALLATION
12. Message LED Lead (MSG LED)
This indicates whether a message has been received from a fax/modem.
The
LED will remain lit when there is no signal and blink when there is data transfer
or waiting in the inbox).
13. SMI Suspend Switch Lead (SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the “Turbo Switch”
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
14. ATX Power Switch / Soft Power Switch (PWR SW)
The system power is controlled by a momentary switch connected to this lead.
Pushing the button once will switch the system between ON and SLEEP.
Push-
ing the switch while in the ON mode for more than 4 seconds will turn the
system off.
The system power LED shows the status of the system’s power.
15. Reset Switch Lead (RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system’s power supply.
16. System Power LED (PWR LED)
This 3-pin connector connects the system power LED, which lights when the
system is powered on and blinks when it is in sleep mode.
17. Keyboard Lock Switch Lead (KEYLOCK, 2 pins)
This 2-pin connector connects to the case-mounted keyboard lock switch to al-
low keyboard locking.
18. Speaker Connector (SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
System Panel Connections
PLED#
Ground
MLED
PWRBT#
*
Requires an ATX power supply.
KLock#
+5 Volts
SPKR
Keyboard Lock
Speaker
Connector
Power LED
Ground
+5 Volts
Reset SW
SMI Lead
Message
LED
ATX Power
Switch*
ExtSMI#
ResetCon
Ground
Ground
Ground
Ground
+5 Volts