Asus SP97-XV User Manual - Page 38

ASUS SP97-XV User's Manual, Autodetection of Hard Disks on Bootup, Drive A / Drive B None, Floppy 3

Get Asus SP97-XV PDF manuals and user guides View all Asus SP97-XV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

IV. BIOS SOFTWARE The MODE entry is for IDE hard disks only, and can be ignored for MFM and ESDI drives. This entry provides three options: Normal, Large, LBA, or Auto (see below). Set MODE to the Normal for IDE hard disk drives smaller than 528MB; set it to LBA for drives over 528MB that support Logical Block Addressing (LBA) to allow larger IDE hard disks; set it to Large for drives over 528MB that do not support LBA. Large type of drive can only be used with MS-DOS and is very uncommon. Most IDE drives over 528MB support the LBA mode. Autodetection of Hard Disks on Bootup For each field, Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE disk drives during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type. If you use older hard disks that do not support this feature, then you must configure the hard disk in the standard method as described earlier using the "User" option. NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Drive A / Drive B (None) These fields record the types of floppy disk drives installed in your system. The available options for drives A and B are 360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB, 3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None. To enter the configuration value for a particular drive, highlight its corresponding field and then select the drive type using the left or right arrow keys. Floppy 3 Mode Support (Disabled) This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5-inch disk drive. This is normally disabled but you may choose from either Drive A, Drive B, Both, or Disabled. Video (EGA/VGA) Set this field to the type of video display card installed in your system. The options are EGA/VGA, CGA 40, CGA 80, and Mono (for Hercules or MDA). If you are using a VGA or any higher resolution card, choose EGA/VGA. Halt On (All Errors) This field determines which types of errors will cause the system to halt. Choose from either All Errors; No Errors; All, But Keyboard; All, But Diskette; or All, But Disk/Key. IV. BIOS (Standard CMOS) 38 ASUS SP97-XV User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
ASUS SP97-XV User’s Manual
38
IV.
BIOS SOFTWARE
IV.
BIOS
(Standard CMOS)
The
MODE
entry is for IDE hard disks only, and can be ignored for MFM and ESDI
drives. This entry provides three options:
Normal, Large, LBA
, or
Auto
(see below).
Set
MODE
to the
Normal
for IDE hard disk drives smaller than 528MB; set it to
LBA
for drives over 528MB that support Logical Block Addressing (LBA) to allow
larger IDE hard disks; set it to
Large
for drives over 528MB that do not support
LBA.
Large
type of drive can only be used with MS-DOS and is very uncommon.
Most IDE drives over 528MB support the
LBA
mode.
Autodetection of Hard Disks on Bootup
For each field, Primary Master, Primary Slave, Secondary Master, and Secondary
Slave, you can select
Auto
under the TYPE and MODE fields. This will enable auto
detection of your IDE disk drives during bootup. This will allow you to change your
hard disks (with the power off) and then power on without having to reconfigure
your hard disk type. If you use older hard disks that do not support this feature, then
you must configure the hard disk in the standard method as described earlier using
the “User” option.
NOTE:
After the IDE hard disk drive information has been entered into BIOS, new
IDE hard disk drives must be partitioned (such as with FDISK) and then formatted
before data can be read from and write on. Primary IDE hard disk drives must have
its partition set to
active
(also possible with FDISK).
NOTE:
SETUP Defaults are noted in parenthesis next to each function heading.
Drive A / Drive B (None)
These fields record the types of floppy disk drives installed in your system.
The
available options for drives A and B are
360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB,
3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None.
To enter the configuration value for a particular drive, highlight its corresponding
field and then select the drive type using the left or right arrow keys.
Floppy 3 Mode Support (Disabled)
This is the Japanese standard floppy drive.
The standard stores 1.2MB in a 3.5-inch
disk drive.
This is normally disabled but you may choose from either
Drive A
,
Drive
B
,
Both
, or
Disabled.
Video (EGA/VGA)
Set this field to the type of video display card installed in your system.
The options
are
EGA/VGA
,
CGA 40
,
CGA 80
,
and Mono (for Hercules or MDA).
If you are using
a VGA or any higher resolution card, choose
EGA/VGA
.
Halt On (All Errors)
This field determines which types of errors will cause the system to halt.
Choose from
either
All Errors
;
No Errors
;
All, But Keyboard
;
All, But Diskette
; or
All, But Disk/Key.