Asus Terminator C3 Terminator C3V User Manual - Page 33

Replacing the cover

Get Asus Terminator C3 PDF manuals and user guides View all Asus Terminator C3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2.10 Replacing the cover After you have installed all the internal components and you have connected all the necessary cables, you are now ready to put the system back together. Follow these steps to re-assemble the system. 1. With the chassis lying on its side, hook the swivel edge of the drive frame to the main chassis. 2. Sway the drive frame inward until it fits completely. The side tabs on both ends of the drive frame should snap perfectly to the chassis edge. 3. Re-attach the power socket module and secure it with the screw you removed earlier. Side tab 4. Turn the chassis upright. 5. Place the cover over the chassis leaving about two inches from the rear panel. ASUS Terminator 1 C3 barebone system 2-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
ASUS Terminator 1 C3 barebone system
ASUS Terminator 1 C3 barebone system
ASUS Terminator 1 C3 barebone system
ASUS Terminator 1 C3 barebone system
ASUS Terminator 1 C3 barebone system
2-17
2-17
2-17
2-17
2-17
2.10
Replacing the cover
After you have installed all the internal components and you have
connected all the necessary cables, you are now ready to put the system
back together.
Follow these steps to re-assemble
the system.
1.
With the chassis lying on its
side, hook the swivel edge of
the drive frame to the main
chassis.
2.
Sway the drive frame inward
until it fits completely. The
side tabs on both ends of the
drive frame should snap
perfectly to the chassis edge.
3.
Re-attach the power socket
module and secure it with the
screw you removed earlier.
4.
Turn the chassis upright.
5.
Place the cover over the
chassis leaving about two
inches from the rear panel.
Side tab
Side tab
Side tab
Side tab
Side tab