Behringer DEEPMIND 6 Manual - Page 59

59 DeepMind 6 User Manual • RATE - This option is the same as the physical LFO RATE fader on the surface. Any changes to the LFO RATE fader will be reflected here. The LFO RATE range is from 0 to 255, with 0 being 0.05371 Hz and 255 being 65.4 Hz. The default LFO RATE setting is 0. Note: When the ARP-SYNC is ON, the RATE parameter is not shown, but CLOCK-DIVIDE instead. This menu shows values that are based on the time division of the Master BPM RATE as shown below: Note: For a timing diagram please consult the section later in this document. • ARP SYNC - This option allows you to turn Arpeggiator Synchronisation On and Off. When ARP-SYNC is On, the LFO waveform will synchronize to the Master BPM. When ARP-SYNC is off, the LFO will run at the rate set by the LFO RATE fader parameter. LFO (ARP SYNC OFF) LFO ARP SYNC ARP CLOCK LFO (ARP SYNC ON) RATIO DESCRIPTION 4 Four notes 3 Three notes 2 Two notes 1 One note 1/2 Half note 3/8 Dotted quarter note 1/3 Third note (Half note triplets) 1/4 Quarter note 3/16 Dotted eighth note 1/6 Sixth note (Quarter note triplets) 1/8 Eighth note 3/32 Dotted sixteenth note 1/12 Twelfth note (Eighth note triplets) 1/16 Sixteenth note 3/64 Dotted thirty-second note 1/24 Twenty-fourth note (Sixteenth note triplets) 1/32 Thirty-second note 3/128 Dotted sixty-fourth note 1/48 Forty-eighth note (Thirty-second note triplets) 1/64 Sixty-fourth note • KEY SYNC - This option allows you to turn Key Synchronisation On or Off. When KEY-SYNC is On, the LFO waveform generation will be reset as you strike a note (keeping in mind the LFO DELAY TIME is also part of the waveform generation). When KEY-SYNC is Off, the LFO will free run. The default ARP-SYNC setting is Off. • SLEW-RATE - This option allows you to smooth out the transitions of the LFO waveform. The SLEW RATE reduces the rate of change of the LFO waveform shape. LFO SLEW RATE 0 85 170 255 The SLEW RATE range is from 0-255, with 0 being no change, and 255 full smoothing. The default SLEW RATE setting is 0. • PHASE - As each voice has independent LFOs, this option allows you to control the phase relationship between the LFO waveforms. • POLY - All voices use an independent LFO. This is the default mode. • MONO - All voices use a common LFO. • SPREAD - With a setting of 1, there is a 1 degree shift between the LFOs for each voice. As you begin to increase the SPREAD value, the phase of the LFO for each consecutive voice will be shifted by the amount of SPREAD applied. For example, with a 90 degree setting, the first voice will always be at 0 degrees, and each consecutive voice will be shifted by an additional 90 degrees. So with 4 voice UNISON, voice 1 would be at 0 degrees, voice 2 would be at 90 degrees, voice 3 would be at 180 degrees, and voice 4 would be at 270 degrees. LFO PHASE SPREAD (UNISON 4 SHOWN) 45 LFO (KEY SYNC OFF) KEY GATE LFO (KEY SYNC ON) LFO KEY SYNC 90 180 225 VOICE 1 LFO VOICE 2 LFO VOICE 3 LFO VOICE 4 LFO The default KEY-SYNC setting is Off. The PHASE SPREAD range is from 1-254 degrees. The default PHASE setting is POLY. 5. To exit the LFO EDIT menu, press the EDIT switch again (or press the PROG switch) to return the main display.