Beretta SV10 Perennia I KO Instruction Manual - Page 52

Routine Field Stripping

Get Beretta SV10 Perennia I KO PDF manuals and user guides View all Beretta SV10 Perennia I KO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

• Move the selector to the second position. (On some models this is not possible since the selector is blocked by a screw.) NOTICE: If the gun features a NON-SELECTIVE SINGLE TRIGGER or a SELECTIVE, BLOCKED TRIGGER (inertia mass type) it is necessary to give a slap to the recoil pad to prepare the firearm to decock the second hammer. • Pull the trigger to decock the second hammer. To remove the snapcaps without recocking the hammers: • Take off the fore-end before you open the gun. • Take out the snapcaps, close the gun and remount the fore-end. ROUTINE FIELD STRIPPING WARNING: Always check that the shotgun is unloaded (empty cartridge chambers). If not, unload it as instructed in the relevant section. ! WARNING: Never point the firearm at someone or at hard and flat surfaces. Always treat the shotgun as if it were loaded. ! The routine disassembly is required for cleaning operations every time the gun is fired or before storage in its case. • Completely pull the fore-end catch lever down to detach the fore-end (Fig. 16). • Pull the front of the fore-end down and rotate the fore-end around the hinge pins to remove the fore-end from the barrels (Fig. 16). NOTICE: ONCE THE FORE-END IS DETACHED, DO NOT PULL IT TOO FAR DOWN BEFORE PULLING IT FORWARD! • Rotate the top lever to the right. • Pivot the barrels in a downward motion, taking care to hold them firmly in order to avoid the risk they accidentally disengage the hinge pins and fall. • Lift the barrels out of the receiver. Disengage Monobloc recesses from hinge pins. The top lever remains open. To store the gun in the supplied guncase: • Remount the fore-end on the barrels and press it to catch the barrel hook. NOTICE: It is advisable to place the top lever in its centered position when the shotgun is being stored or trasnported in a gun case. Proceed as follows: move the top lever completely to the right and at the same time press the top lever plunger (located on the top left section of the breechface of the receiver) Fig 17. Once the top lever plunger is completely depressed, release the top lever to its centered position. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
52
• Move the selector to the second position.
(On some models this is not
possible since the selector is blocked by a screw.)
NOTICE:
If the gun features a NON-SELECTIVE SINGLE
TRIGGER or a SELECTIVE,
BLOCKED TRIGGER (inertia mass type) it is necessary to give a slap to the recoil
pad to prepare the firearm to decock the second hammer.
•
Pull the trigger to decock the second hammer.
To remove
the snapcaps without recocking the hammers:
•
Take off the fore-end before you open the gun.
•
Take out the snapcaps, close the gun and remount the fore-end.
ROUTINE FIELD STRIPPING
WARNING:
Always check that the shotgun is unloaded (empty cartridge
chambers). If not, unload it as instructed in the relevant section.
WARNING:
Never point the firearm at someone or at hard and flat surfaces.
Always treat the shotgun as if it were loaded.
The routine
disassembly is required for cleaning operations every time the gun
is fired or before storage
in its case.
•
Completely pull the fore-end catch lever down to detach the fore-end (
Fig. 16
).
• Pull
the front of the fore-end down and rotate the fore-end around the hinge
pins to remove the fore-end from the barrels (
Fig. 16
).
NOTICE:
ONCE THE FORE-END IS DETACHED, DO NOT PULL IT
TOO FAR DOWN
BEFORE PULLING IT FORWARD!
•
Rotate the top lever to the right.
•
Pivot the barrels in a downward motion, taking care to hold them firmly in order
to avoid the risk they accidentally disengage the hinge pins and fall.
•
Lift the barrels out of the receiver. Disengage Monobloc recesses from hinge
pins. The top lever remains open.
To store
the gun in the supplied guncase:
•
Remount the fore-end on the barrels and press it to catch the barrel hook.
NOTICE:
It is advisable to place the top lever in its centered position when the
shotgun is being stored or trasnported in a gun case. Proceed as follows:
move
the top lever completely to the right and at the same time press the top lever
plunger (located on the top left section of the breechface of the receiver)
Fig 17
.
Once the top lever plunger is completely depressed, release the top lever to its
centered position.
!
!