Bosch WTVC6330US User Manual - Page 11

11

24.

Reinstall

the

dryer

door by sliding it

onto the

hinge

pins.

Avoid allowing

the

four plastic

bushings to

fall

off the

hinge

pins.

If any fall

off,

reinstall them

on the

hinge

pins prior

to

reinstalling

the

dryer

door.

reinstall

the

dryer

door

25.

Reinstall

the

hinge

cover plate

removed in

step 4.

Insert and

tighten

the

4

screws

holding

the

hinge

cover

plate

in

place.

reinstall

four

screws

and

tighten

securely

26.

Install

the

plastic

cover plate

over

the original

hinge

position at the

right

hand side

of the

dryer door

opening.

Insert

and tighten the

two

screws holding

the

plate

in

place.

27.

Test

that

the

door

opens

and

closes properly.

The

door should

latch securely.

The

hinge

reversal

process is complete.

Minimum Distances

Important information

concerning

minimum

distances:

-

Depending

on

the

location

of

the

exhaust

air

connection,

an

additional minimum distance

of

5½ inch

(14

cm) must

be

provided

on this

side,

the

side

the

connection

is

on,

for

ducts/brackets

(see

page

19).

-

Benefits

of

maintaining

greater

distance

(clearances) than

the

minimum shown

include:

S

more

air

cools

the

dryer,

keeps

the

dryer

from overheating,

and

improves

drying

performance.

S

reduction

of

the

risk

of

mold

formation

behind

the

appliance.

S

reduced

noise

transmission

S

facilitation

of

installation

and

service.

-

If

the

dryer

is

installed

in

a

small

room,

the

doors

of

the

room must

be

fitted

with

vents

of

the

specified

minimum size.

Refer

to

the

following

illustrations

of

enclosed

installations

for

additional

information.

-

Allow

additional clearance

for

door,

wall and

window

molding

where

necessary.

Installation

Types

Observe the

following

minimum

clearances

between

the

dryer

and

adjacent surfaces

for

all installation

types.

Minimum Installation

Clearances

A

Sides

0.25 in. (6.4 mm)

B

Top

0.25 in. (6.4 mm)

C

Rear*

5.25 in. (13.4 cm)

D

Front

0.50 in. (12.8 mm)

*

as

close to wall

as venting

or

water

connection

will

allow.

If installed

with

a

washer,

the larger

rear

clearance for

dryer

venting

is required

for

the laundry pair.

q

Units

are

designed

so

that

the

dryer

can

be

stacked

on

top

of

the

washer

using

one

of

the

stacking

kits

shown

on

page

19.

q

Units

are

designed

to

allow

for

under-counter

installation

See

required

dimensions

in

under-

counter

installation

section

on

page

12.

Height measurements

shown

in

this

section are

with

the

dryer

feet

at

minimum

extension

(turned

in

all the

way up against

the

base

of

the

dryer).

Recessed or Closet

Dimensions for

installation

in

a

closet or

recessed

area

are

shown

in

the

illustration

below.

Closet Ventilation

Requirements

E

Top

48 sq. in. (310 sq.

cm)

F

Bottom

24 sq. in. (155 sq.

cm)

Required Installation

Space

G

Height

37.25 in. (94.6 cm)

H

Width

27.50 in. (69.9 cm)

I

Depth

37.25 in. (94.6 cm)

Mounted

on

Pedestal

Dimensions for

pedestal

mounting

installation

are

shown

in the

illustration

below.

J

Required Installation

Space

G

Height

52.25 in. (132.7 cm)

H

Width

27.50 in. (69.9 cm)

I

Depth

37.25 in. (94.6 cm)

J

Pedestal Ht.

15.0 in. (38.1 cm)

i

Appliance

must

not be

mounted

on

a

pedestal for

under counter

installations.

Bosch WTVC6330US User Manual - Page 11

Installation, Types - stack kit

Page 11 highlights