Bowflex Ultimate Assembly and Owners Manual - Page 103

T, U1, U

Get Bowflex Ultimate PDF manuals and user guides View all Bowflex Ultimate manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Assembling Your Bowflex® Ultimate™ Leg Assembly A-15 Step 3: LEG EXTENSION SEAT INSTALLATION Locate the following parts: • Leg extension assembly (from previous step) • Leg extension seat assembly (Item #61) • Two (2) 1/4"X2-3/4" bolt (Item #71) • Two (2) 1/4" nylon lock nuts (Item #72) • Four (4) 1/4" washers (Item #55)  Place the leg extension seat (Item #61) on top of the horizontal tube on the leg extension assembly (Item #62) with the hinge brackets facing the direction shown in Figure T.  Insert two 1/4"X2-3/4" bolts (Item #71) with 1/4" washers (Item #55) through the brackets on the bottom of the leg extension seat (Item #61).  Install 1/4" washers (Item #55) onto the bolts and securely tighten 1/4" nylon lock nuts (Item #72) on the bolts. Components for this step are in the Leg Extension Box 61 72 55 Figure T Hinges 55 71 Unit appears like this following this assembly step Step 4: INSTALLING THE LEG EXTENSION CHROME TUBES AND FOAM ROLLERS Locate the following parts • Portion of leg extension attachment already assembled • Three (3) leg extension chrome tubes (Item #66) • Six (6) leg extension rollers (Item #65) • Six (6) leg extension tube end caps (Item #69) • Two (2) 73.50" leg extension cables (Item #67) Components for this step are in Leg Extension Box Figure U 69 65 66  Back out the screws that are in the end holes of the leg extension pivot tube (Item #64) just enough to slide the chrome tube through the holes.  Slide Chrome tubes into all three holes as shown in Figure U.  Slide the LARGE LOOP of the leg extension cables (Item #67) onto the lowest chrome tube, one on each side of the leg extension pivot tube.  Slide the foam rollers (Item #65) onto the chrome tubes (Item #66) as shown in Figure U1.  Push the roller end caps (Item #69) into the ends of the chrome tubes (Item #66) as shown in Figure U1. Unit appears like this following this assembly step Note: You may need to use a rubber mallet to get the end caps securely into the chrome tubes. Figure U1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
A-1³
Assembling Your Bowflex
®
Ultimate
™
Leg Assembly
Figure T
Step 3: LEG EXTENSION SEAT INSTALLATION
Locate the following parts:
• Leg extension assembly (from previous step)
• Leg extension seat assembly
(Item #61)
• Two (2) 1/4”X2-3/4” bolt
(Item #71)
• Two (2) 1/4” nylon lock nuts
(Item #72)
• Four (4) 1/4” washers
(Item #55)
Place the leg extension seat
(Item #61)
on top of
the horizontal tube on the leg extension assembly
(Item #62)
with the hinge brackets facing the
direction shown in Figure T.
Insert two 1/4”X2-3/4” bolts
(Item #71)
with 1/4”
washers
(Item #55)
through the brackets on the
bottom of the leg extension seat
(Item #61)
.
Install 1/4” washers
(Item #55)
onto the bolts and
securely tighten 1/4” nylon lock nuts
(Item #72)
on
the bolts.
Hinges
71
72
55
55
61
Unit appears like
this following this
assembly step
Step 4: INSTALLING THE LEG EXTENSION
CHROME TUBES AND FOAM ROLLERS
Locate the following parts
• Portion of leg extension attachment already
assembled
• Three (3) leg extension chrome tubes
(Item #66)
• Six (6) leg extension rollers
(Item #65)
• Six (6) leg extension tube end caps
(Item #69)
• Two (2) 73.50” leg extension cables
(Item #67)
Back out the screws that are in the end holes of the
leg extension pivot tube
(Item #64)
just enough to
slide the chrome tube through the holes.
Slide Chrome tubes into all three holes as shown in
Figure U.
Slide the
LARGE LOOP
of the leg extension cables
(Item #67)
onto the lowest chrome tube, one on each
side of the leg extension pivot tube.
Slide the foam rollers
(Item #65)
onto the
chrome tubes
(Item #66)
as shown in Figure
U1.
Push the roller end caps
(Item #69)
into
the ends of the chrome tubes
(Item #66)
as
shown in Figure U1.
Note: You may need to use a rubber
mallet to get the end caps securely into
the chrome tubes.
Figure U1
69
65
66
Unit appears like
this following
this assembly
step
Components for this step are
in the Leg Extension Box
Components for
this step are in Leg
Extension Box
Figure U