Bowflex Ultimate Assembly and Owners Manual - Page 98

O, N - 2 review

Get Bowflex Ultimate PDF manuals and user guides View all Bowflex Ultimate manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

A-10 Assembling Your Bowflex® Ultimate™ Step 13: LOWER LAT CROWN INSTALLATION Locate the following parts for this step: • Lower lat crown (Item #76)  Press Lower Lat Tower Crown (Item #76) into open end of lower lat tubing to finish off. Bottom surface of lower lat 76 crown should be in contact with incline bench rest. Note: if you have attached a lat tower, skip this step and discard this piece. Components for this step are in Box 4 Figure N 25 Step 14: BENCH REST BRACKET INSTALLATION Locate the following parts for this step: • Bench (Item #25) 26 • Bench rest bracket (Item #26) • O ne (1) 1/4"X1-1/2" phillips head screws (Installed on the bench) • Three (3) 1/4" Washers (Installed on the bench) • Two (2) 1/4"X 2-1/4" phillips head screws (Installed on the bench)  Remove one (1) 1/4"X2-1/4" phillips head screw, two (2) 1/4"X 2-1/4" phillips head screws and three (3) 1/4" Washers from the back of the bench.  Assemble the bench rest bracket (Item #26) to the back of the bench (Item #25) using the hardware above as shown in Figure O. Note: Double check to make sure bench is stable in the incline position and the foot rest assembly is properly positioned when the bench is in the flat position. in the flat position, the bench should NOT rest on the foot rest. Please inspect your machine to ensure that all fasteners are tight and everything is properly assembled. Review all warnings that are affixed to the machine. Figure O Components for this step are in Box 3 & Box 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
A-10
Figure O
Step 14: BENCH REST BRACKET INSTALLATION
Locate the following parts for this step:
• Bench
(Item #25)
• Bench rest bracket
(Item #26)
• One (1) 1/4”X1-1/2” phillips head screws
(Installed on
the bench)
• Three (3) 1/4” Washers
(Installed on the bench)
• Two (2) 1/4”X 2-1/4” phillips head screws
(Installed on
the bench)
Remove one (1) 1/4”X2-1/4” phillips head screw, two (2) 1/4”X
2-1/4” phillips head screws and three (3) 1/4” Washers from the
back of the bench.
Assemble the bench rest bracket
(Item #26)
to the back of the
bench
(Item #25)
using the hardware above
as shown in Figure O.
Note: Double check to make sure bench is stable in the
incline position and the foot rest assembly is properly
positioned when the bench is in the flat position. in the
flat position, the bench should NOT rest on the foot rest.
Please inspect your machine to ensure that all fasteners
are tight and everything is properly assembled. Review all
warnings that are affixed to the machine.
26
25
Components for
this step are in
Box 3 & Box 4
Step 13: LOWER LAT CROWN INSTALLATION
Locate the following parts for this step:
• Lower lat crown
(Item #76)
Press Lower Lat Tower Crown
(Item #76)
into open end of
lower lat tubing to finish off. Bottom surface of lower lat
crown should be in contact with incline bench rest.
Note: if you have attached a lat tower, skip this step and
discard this piece.
Components for
this step are in
Box 4
Figure N
76
Assembling Your Bowflex
®
Ultimate
™