Brother International LS2300PRW Users Manual - English and Spanish - Page 11

Threading The Machine - bobbins

Get Brother International LS2300PRW PDF manuals and user guides View all Brother International LS2300PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

THREADING THE MACHINE Winding the bobbin 1 This section describes how to wind the thread onto the bobbin. 1 Pulling it in as far as possible. a Pre-tension disk b Bobbin winder shaft c Bobbin CAUTION ● Only use bobbins (part code: SA156, SABOBBIN, SFB: XA5539-151) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine. ● We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SABOBBIN, SFB: XA5539-151). Actual size This model a 11.5 mm (7/16 inches) Pull up the spool pin as far as possible, and a then put a spool of thread on this pin. Pass the thread around the pre-tension disk. b CAUTION ● If the spool of thread is not in the right place, the thread may tangle on the spool pin. Pass the end of the thread through the hole on c the bobbin from the inside of the bobbin. Put the bobbin onto the bobbin winder shaft and d slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the groove of the bobbin. Other models Turn on the sewing machine. e While holding the end of the thread, gently f press the foot controller to wind the thread around the bobbin a few times. Then stop the machine. a Spring on the shaft b Groove of the bobbin 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
10
1
THREADING THE MACHINE
Winding the bobbin
This section describes how to wind the thread onto the bobbin.
a
Pre-tension disk
b
Bobbin winder shaft
c
Bobbin
a
Pull up the spool pin as far as possible, and
then put a spool of thread on this pin.
b
Pass the thread around the pre-tension disk.
c
Pass the end of the thread through the hole on
the bobbin from the inside of the bobbin.
d
Put the bobbin onto the bobbin winder shaft and
slide the bobbin winder shaft to the right. Turn
the bobbin clockwise, by hand, until the spring
on the shaft slides into the groove of the bobbin.
e
Turn on the sewing machine.
f
While holding the end of the thread, gently
press the foot controller to wind the thread
around the bobbin a few times. Then stop the
machine.
●
Only use bobbins (part code: SA156, SABOBBIN, SFB: XA5539-151) that have been designed for this
sewing machine. Using other bobbins may cause damage to the machine.
●
We designed the bobbin that comes with this machine. If you use bobbins from other models, the
machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the
same type (part code: SA156, SABOBBIN, SFB: XA5539-151).
a
11.5 mm (7/16 inches)
1
Pulling it in as
far as possible.
CAUTION
Actual size
This model
Other models
●
If the spool of thread is not in the right place,
the thread may tangle on the spool pin.
a
Spring on the shaft
b
Groove of the bobbin
CAUTION