Brother International S-7200C Instruction Manual - English - Page 33

Using the lower thread counter, USING THE G50 OPERATION PANEL BASIC OPERATIONS

Get Brother International S-7200C PDF manuals and user guides View all Brother International S-7200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 5-7. Using the lower thread counter y The lower thread counter can be used to let you know approximately how much lower thread is remaining. y The value displayed by the lower thread counter display is reduced by 1 from the initial setting value each time the sewing machine sews 10 stitches, and a warning is given when the counter goes below"0". 1 After about 2 seconds, the buzzer will sound and the lower thread counter display will show the initial value which was set previously. (Press for 2 seconds or more) 2 y When the + key is pressed, the setting increases. y When the - key is pressed, the setting decreases. y If you hold down the keys, the setting will change more quickly. y If a value of "0" is set, the lower thread counter will not operate. y The initial setting value will be accepted when sewing starts. 4182M (Initial value) Reduces by 1 for every 10 stitches sewn (Buzzer sounds for 5 seconds) Sewing is possible until thread trimming is carried out. 4183M Press the RESET key (2). 4184M 1. When sewing is carried out, the value shown in the lower thread counter display is reduced by 1 for every 10 stitches sewn. (When the value goes below zero ("0"), a minus sign appears and counting continues to a maximum of "-999".) 2. When the value goes below "0", a warning icon (1) illuminates and an electronic buzzer sounds for 5 seconds. 3. Sewing will be possible even after the treadle is returned to the neutral position and the sewing machine stops. However, after the treadle has been depressed backward and thread trimming has been carried out, sewing using the treadle will no longer be possible. 4. When the RESET key (2) is pressed, the warning icon (1) will switch off and the display will return to showing the initial values. Sewing using the treadle will then be possible. S-7200C 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
S-7200C
5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS)
26
5-7. Using the lower thread counter
y
The lower thread counter can be used to let you know approximately how much lower thread is remaining.
y
The value displayed by the lower thread counter display is reduced by 1 from the initial setting value each time the sewing
machine sews 10 stitches, and a warning is given when the counter goes below“0”.
<Initial value setting>
1
(Press for 2 seconds or more)
After about 2 seconds, the buzzer will sound and the lower thread counter display
will show the initial value which was set previously.
2
y
When the + key is pressed, the setting increases.
y
When the - key is pressed, the setting decreases.
y
If you hold down the keys, the setting will change more quickly.
y
If a value of “0” is set, the lower thread counter will not operate.
y
The initial setting value will be accepted when sewing starts.
<Lower thread counter operation>
1. When sewing is carried out, the value shown in the lower thread counter display is reduced by 1 for every 10 stitches sewn.
(When the value goes below zero (“0”), a minus sign appears and counting continues to a maximum of “-999”.)
2. When the value goes below “0”, a warning icon (1) illuminates and an electronic buzzer sounds for 5 seconds.
3. Sewing will be possible even after the treadle is returned to the neutral position and the sewing machine stops.
However,
after the treadle has been depressed backward and thread trimming has been carried out, sewing using the treadle will no
longer be possible.
4. When the RESET key (2) is pressed, the warning icon (1) will switch off and the display will return to showing the initial
values. Sewing using the treadle will then be possible.
4182M
4183M
4184M
(Initial value)
Reduces by 1
for every 10
stitches sewn
Press the RESET key (2).
(Buzzer sounds for 5 seconds)
Sewing is possible
until thread trimming
is carried out.