Brother International S-7200C Instruction Manual - English - Page 59

GuCt will appear in the display 1., Press the end backtack key 5.

Get Brother International S-7200C PDF manuals and user guides View all Brother International S-7200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

11. CLEANING Turn the machine pulley to lower the needle bar until the hole is visible. 4241M 4242M 4243M 1. Turn the power switch to "OFF". 2. Remove the screws and the set screws. 3. Apply grease to each of the holes until the grease overflows slightly. 4. Tighten the screws and the set screws in order to push the grease in. 5. Turn the machine pulley by hand to move the needle bar up and down several times in order to disperse the grease. 6. Use a cloth to wipe away any excess grease from around the screws and set screws and from underneath needle bar bush D. 7. Carry out the reset procedure given below. After the grease has been applied, carry out the following procedure to reset the grease consumption amount. 1. While pressing the key (3) and the key (4) at the right end simultaneously, press the power ON switch. 2. "GuCt" will appear in the display (1). 3. Press the end backtack key (5). 4. The indicator of the end backtack key (5) will illuminate and the display (1) will change to showing "xxx". ("xxx" represents the amount of grease consumed.) For example, "100" means that 100% of the grease has been consumed. 5. Press the continuous backtack key (6) for 2 seconds or more. 6. The display (1) will change to " 0". 7. Press the thread wiper key (2). The display (1) will change to stitch number display mode and treadle operation will be possible. (This completes the reset procedure.) 2138M 2139M S-7200C 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
S-7200C
11. CLEANING
52
1. Turn the power switch to “OFF”.
2. Remove the screws and the set screws.
3. Apply grease to each of the holes until the grease
overflows slightly.
4. Tighten the screws and the set screws in order to push
the grease in.
5. Turn the machine pulley by hand to move the needle bar
up and down several times in order to disperse the
grease.
6. Use a cloth to wipe away any excess grease from around
the screws and set screws and from underneath needle
bar bush D.
7. Carry out the reset procedure given below.
<Resetting the grease consumption amount>
After the grease has been applied, carry out the following procedure to reset the grease consumption amount.
1. While pressing the
key (3) and the
key (4) at the right end simultaneously, press the power ON switch.
2. “GuCt” will appear in the display (1).
3. Press the end backtack key (5).
4. The indicator of the end backtack key (5) will illuminate and the display (1) will change to showing “xxx”. (“xxx” represents
the amount of grease consumed.) For example, “100” means that 100% of the grease has been consumed.
5. Press the continuous backtack key (6) for 2 seconds or more.
6. The display (1) will change to “
0”.
7. Press the thread wiper key (2). The display (1) will change to stitch number display mode and treadle operation will be
possible. (This completes the reset procedure.)
<-[]3[]
・
[]5[] specifications >
<-[]5[]specifications >
2138M
2139M
4241M
4242M
Turn the
machine pulley
to lower the
needle bar until
the hole is
visible.
4243M