Brother International S-7200C Instruction Manual - English - Page 62

Adjusting the safety switch position, STANDARD ADJUSTMENTS, <Adjustment method&gt

Get Brother International S-7200C PDF manuals and user guides View all Brother International S-7200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

13. STANDARD ADJUSTMENTS 13-2. Adjusting the safety switch position 4249M The safety switch (1) is normally installed as shown in figure [A]. However, if the processing method used for the table leaves too much space between the machine head and the table hole, it may adversely affect the operation of the safety switch (1). The standard amount of clearance between the machine head and the table hole is 1.5 mm. If the clearance is 3.5 mm or more, install the safety switch (1) so that the washer (2) is on the machine head side as shown in Figure [B]. * If the position cannot be satisfactorily adjusted in this way, add more washers of the same thickness. 3691M If the spring stroke is too small, the safety switch will not operate. 3.5 mm or more Sewing machine Table Clearance is too large. By changing the position of the safety switch, the required spring stroke can be maintained. 3690M Reduce the clearance. 3692M 55 S-7200C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
S-7200C
13. STANDARD ADJUSTMENTS
55
13-2. Adjusting the safety switch position
The safety switch (1) is normally installed as shown in figure
[A].
However, if the processing method used for the table leaves
too much space between the machine head and the table
hole, it may adversely affect the operation of the safety
switch (1).
<Adjustment method>
The standard amount of clearance between the machine
head and the table hole is 1.5 mm.
If the clearance is 3.5 mm or more, install the safety switch
(1) so that the washer (2) is on the machine head side as
shown in Figure [B].
* If the position cannot be satisfactorily adjusted in this way,
add more washers of the same thickness.
<Safety switch operation>
4249M
3690M
3691M
3692M
Sewing
machine
Table
By changing the position of the safety switch,
the required spring stroke can be maintained.
Clearance
is too large.
If the spring stroke is too small, the safety
switch will not operate.
Reduce the clearance.
3.5 mm or more